mypros+
Model reference

Amana ADM-1B-P85548-4S

Range

1 document72 error codes15 service modes

Available documentation

Tech Tip

  • Export Imperial Maytag commercial dryer installation instructions64 pg
    Covers this model
MyPros+ Max

Diagnose your Amana ADM-1B-P85548-4S.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (72)

CodeMeaning
1-1Power relay K2 stuck in closed (active) position, detected by control module.1-2Control module software problem10-1Dispenser electrical problem10-3Drying fan error2-1Stuck key detected2-2No response from user interface3-1Thermistor/soil sensor open circuit3-2Thermistor/soil sensor short circuit3-3Soil sensor (OWI) calibration failure4-3Wash motor non-operation5-1Door switch stuck open5-2Door switch stuck closed6-1No water / insufficient water level in pump (mechanical problem).6-2Fill valve electrical problem6-3Suds/air in pump6-4Overfill float switch stuck in overfill position or dishwasher not level, or…6-7Flow meter disconnected or damaged.6-8Regeneration electrical problem7-1No heat7-2Heater element stuck in active mode8-2Drain motor electrical problem8-3Drain circuit constantly powered9-1Unable to determine diverter valve position9-2Diverter valve stuck9-3Diverter disc missing9-4Lower spray arm errord13The Coin 2 sensor is detected as blocked; coin vault may be full or sensor may…d16No communication from Gend5The Coin 1 sensor is detected as blocked; coin vault may be full or sensor may…d9Incoming voltage detected below 185 VAC (low voltage).
View all 72 error codes
F0 E5Off balance load detected during cycle operation.F01Indicates a main control fault.F03Main control detects an out of range pressure signal from the pressure…F07Main control cannot determine position of shifter (shifter system failure).F1 E1Main control faultF1 E6Control board recognized line voltage below 90 VAC.F11Indicates a fault of the motor control section of the main control.F2 E1Washer keypad stuck errorF20Water level does not change for a period of time, or water is present but main…F21Water level does not change after the drain pump is on for 10 minutes (long…F22Lid lock has not moved into locked position or motor cannot be powered; lid not…F24Inlet water temperature fault; inlet thermistor is detected to be open or…F25Main control cannot determine speed of basket, or speed changes too quickly…F26Lid is in locked state but lid switch is open; main control cannot detect the…F27Main control senses a water level that exceeds the washer's capacity (overflow…F29Lid lock has not moved into unlocked position or motor cannot be powered (lid…F3 E2Pressure sensor faultF3 E3Inlet water temperature faultF32No fill condition detected; water level does not change.F5 E1Lid switch faultF5 E3Lid switch faultF5 E4Lid unlock faultF7 E1Basket speed sensor faultF7 E2Motor control faultF7 E5Shifter faultF70Communication failure between CCU and UI; electrical connection is damaged.F71Communication failure between CCU and UI; electrical connection is damaged.F73The User Interface EEPROM identification does not match the expected value in…F74The User Interface EEPROM identification does not match the expected value in…F77Off balance load detected.F8 E1No fillF8 E3Overflow conditionF9 E1Long drainFC E1Model/serial number not programmedFC E2Model/serial numbers do not match between the Main Control and User Interface…FC E4USB faultFC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication error.

Service modes (15)

  • Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
  • Error History ClearDuring the service diagnostic program at the error display interval, press the HI TEMP (high…
  • Help Mode["First enter Service Mode.","Use the NORMAL keypad to advance to program location 2.xx (Special…
  • P-01 Clear Errors["Enter Service Diagnostic Test Modes.","Display shows P-01.","Press START to clear an active error…
  • P-02 Cycle Credit["Enter Service Diagnostic Test Modes.","Press NORMAL Keypad until P-02 is displayed.","Press START…
  • P-03 Service Diagnostic["Enter Service Diagnostic Test Modes.","Press NORMAL Keypad until P-03 is displayed.","Press START…
  • P-04 Manual Diagnostic["Enter Service Diagnostic Test Modes.","Press NORMAL Keypad until P-04 is displayed.","Press START…
  • P-05 Calibration Cycle["Enter Service Diagnostic Test Modes.","Press NORMAL Keypad until P-05 is displayed.","Press START…
  • P-07 UI Diagnostics["Enter Service Diagnostic Test Modes.","Press NORMAL Keypad until P-07 is displayed.","Press START…
  • P-09 Tachometer Verification["Enter Service Diagnostic Test Modes.","Press NORMAL Keypad until P-09 is displayed.","Press START…
  • P-12 Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Press NORMAL Keypad until P-12 is displayed.","Press START…
  • Service Diagnostic Program1
  • Service Diagnostic Test Modes (Entry)["1. For coin models
  • Service Diagnostic Test Modes (main entry)["For coin (PD) models
  • Technician Service Access Code (PR models, free vend only)["Press the POWERWASH, EXTRA RINSE, TEMPERATURE, and DELICATES key pads within 10 seconds."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass