mypros+
Model reference

Amana AER5715RCB

Range

6 documents39 error codes47 service modes

Available documentation

Tech Sheet

  • Electric Freestanding Range—Technical Information17 pg
    Covers this model
  • Electric Freestanding Range—Technical Information13 pg
    Covers this model
  • Electric Freestanding Range⎯Technical Information11 pg
    Covers this model

Service Manual

  • Service Manual - Electric Freestanding Range36 pg
    Covers this model
  • Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
    Covers this model
  • FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
    Covers this model
MyPros+ Max

Diagnose your Amana AER5715RCB.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (39)

CodeMeaning
1c1cShorted key detected1c2cKeyboard tail disconnected from control board.1c31Cancel key circuit problem1c32Cancel key circuit problem (cavity 2 / lower oven).1c4cMicro communication failure1c5cVcc or ground fault1c6cEEPROM error1c7cControl not calibrated1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error1d11Runaway oven temperature (650°F) detected with door unlocked1d12Runaway oven temperature (650°F) detected with door unlocked (cavity 2).1d21Runaway oven temperature (950°F) detected with door locked1d22Runaway oven temperature (950°F) detected with door locked (cavity 2).3d11Temperature sensor open3d12Oven temperature sensor open circuit (cavity 2).3d21Temperature sensor shorted3d22Oven temperature sensor shorted (cavity 2).3d41Meat probe shorted3d51Meat probe not calibrated4d11Door position switch not closed when door is locked during clean cycle.4d12Door switch position failure4d21No reverse airflow fan rotation detected (no or low RPM).4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse airflow fan is on when it should be off.4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure
View all 39 error codes
4d52Door switch circuit failure9d11Door latch will not lock9d12Door latch will not lock9d21Door latch will not unlock9d22Door latch will not unlock9d31Unlock state unknown9d32Door latch state unknown9d41Unlock state unknown9d51Lock switch not reading locked or unlocked

Service modes (47)

  • 24-Hour Clock TogglePress and hold CANCEL and DELAY pads for 3 to 5 seconds
  • Child LockoutPress and hold CANCEL and COOK & HOLD pads for 3 to 5 seconds until beep sounds.
  • Clock Display TogglePress and hold CANCEL and CLOCK pads for 3 to 5 seconds.
  • Diagnostic Code DisplayWithin 30 seconds of powering up the unit, press and hold the [More+] pad
  • Diagnostic Code Display (H1 Control)Press and hold AUTOSET pad for 3 seconds at power-up
  • Diagnostic Code Display (M1/M2 Control)Press and hold Up Arrow pad and power up the unit simultaneously
  • Diagnostic Code Display Mode["Apply power to the control.","Within 30 seconds of powering up the unit, press and hold the MORE+…
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
  • Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
  • Factory Default ResetPress and hold CANCEL and KEEP WARM pads for 3 to 5 seconds.
  • Faults Access (EOC III Controls)1
  • Faults Access (EOC III)1
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • One-Watt Standby Mode (NSC)Press and hold Cancel and Less
  • Oven Temperature Adjustment1
  • Quick Test1. Within 5 minutes of power-up, press and hold Cancel and Broil pads simultaneously for 3 to 5…
  • Quick Test (H1 Control)1
  • Quick Test (M1/M2 Control)1
  • Quick Test Mode["Must be entered within the first 5 minutes after power-up.","Press and hold Cancel and Broil pads…
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (EOC III)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
  • Sabbath ModeHold CLOCK pad for 3 to 5 seconds to activate Sabbath mode
  • Service Mode (EOC III Controls)1
  • Service Mode (EOC III)1
  • Temperature Display (°F/°C toggle)["Press and hold CANCEL and BAKE pads for 3 to 5 seconds.","Press MORE+ or LESS- pads to change…
  • Temperature Display Toggle (°F/°C)Press and hold CANCEL and BAKE pads for 3 to 5 seconds
  • Temperature Display Toggle (F/C)Press and hold CANCEL and BAKE pads for 3 to 5 seconds
  • Test Mode (UH Control)1
  • Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass