Model reference
Amana AGS5730BDW
Range
13 documents36 error codes39 service modes
Available documentation
Tech Sheet
- Tech Sheet - 1602629110 pg
Service Manual
- range_maytagerrorcodes_joba124 pg
- Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
- Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
- FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
Bulletin
- Installation Bulletin1 pg
- Installation Bulletin - IDC-0009-B-French Metal Leveling Leg1 pg
- Installation Bulletin - IDC-0014-B Side Panel Kit2 pg
- Installation Bulletin - IDC-0014-B-French Side Panel Kit2 pg
- Installation Bulletin - IDC-0013-B Filler Kit2 pg
- Installation Bulletin - IDC-0013-B-French Filler Kit2 pg
Other
- TDC 0099 B1 pg
Installation Guide
- Installation Bulletin2 pg
MyPros+ Max
Diagnose your Amana AGS5730BDW.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (36)
CodeMeaning
1c1cShorted key detected on control circuit board.1c2cKeyboard tail disconnected; keyboard loop improper value.1c31Cancel key circuit problem; cancel key improper value.1c32Cancel key circuit problem; cancel key improper value.1c4cPower micro communication failure (CRC invalid).1c6cEEPROM error; no response from EEPROM after 3 tries.1c7cControl not calibrated; calibration value out of range.1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error; CRC invalid.1d11Runaway temperature (650°F) detected, door unlocked; sensor resistance > 2237…1d12Runaway temperature (650°F) detected, door unlocked; sensor resistance > 2237…1d21Runaway temperature (950°F) detected, door locked; sensor resistance > 2787…1d22Runaway temperature (950°F) detected, door locked; sensor resistance > 2787…3d11Temperature sensor open; sensor resistance reads infinite Ohms.3d12Temperature sensor open; sensor resistance reads infinite Ohms.3d21Temperature sensor shorted; sensor resistance reads 0 Ohms.3d22Temperature sensor shorted; sensor resistance reads 0 Ohms.3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch position failure; door switch not closed when door is locked.4d12Door switch position failure; door switch not closed when door is locked.4d21No reverse airflow fan rotation (no or low RPM).4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse airflow fan state error (on when it should be off).4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure; door switch not open or closed.4d52Door switch circuit failure; door switch not open or closed.View all 36 error codes
9d11Latch will not lock; lock switch not closed.9d12Latch will not lock; lock switch not closed.9d21Latch will not unlock; unlock switch not closed.9d22Latch will not unlock; unlock switch not closed.9d31Latch state unknown; both locked and unlocked switches indicate active…9d32Latch state unknown; both locked and unlocked switches indicate active…
Service modes (39)
- 24-Hour Clock TogglePress Cancel and Favorite pads simultaneously for 5 seconds.
- Clock Display Disable/EnablePress and hold Cancel and Clock pads simultaneously for 5 seconds.
- Control LockPress Cancel and Cook & Hold pads simultaneously for 5 seconds to enable.
- Diagnostic Code DisplayPress and hold the Autoset 0 pad for 5 seconds while powering up the unit
- Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
- Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
- Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
- Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
- Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
- Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
- Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
- Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
- Factory Default ResetPress and hold Cancel and Keep Warm pads simultaneously for 5 seconds.
- Faults Access (EOC III Controls)1
- Faults Access (EOC III)1
- One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
- One-Watt Standby Mode (NSC)Press and hold Cancel and Less
- Oven Temperature AdjustmentPress Bake pad and enter 550°F
- Quick TestPress and hold the Cancel and Broil pads simultaneously for 5 seconds at power-up, or within 5…
- Quick Test Mode (EOC III Controls)1
- Quick Test Mode (EOC III)1
- Quick Test Mode (H1 Controls - Convection Model)1
- Quick Test Mode (H1 Controls - Non-Convection Model)1
- Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
- Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
- Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
- Quick Test Mode (H2/H2.5 Controls)1
- Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
- Quick Test Mode (H3 Controls)1
- Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
- Quick Test Mode (M1/M2 Controls)1
- Quick Test Mode (NSC Non-Self Clean Controls)1
- Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
- Service Mode (EOC III Controls)1
- Service Mode (EOC III)1
- Temperature Display Toggle (°F/°C)Press and hold Cancel and Bake pads simultaneously for 5 seconds.
- Test Mode (UH Control)1
- Test Mode (UH Controls)1
- Twelve Hour Off / Sabbath ModePress and hold Clock pad for 5 seconds.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana range models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass