mypros+
Model reference

Amana CCU-516

Range

4 documents48 error codes19 service modes

Available documentation

Tech Sheet

  • techsheet 818267716 pg
    Covers this model
  • Tech Sheet 818267716 pg
    Covers this model
  • Tech Sheet 818220812 pg
    Covers this model
  • Service Technician Technical Sheet 818220812 pg
    Covers this model
MyPros+ Max

Diagnose your Amana CCU-516.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (48)

CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF/01No water entering machine detected within 30 seconds (valves turned off) OR…F/02Drain time exceeds eight minutes; water valves are turned off.F/05Water temperature sensor (NTC) value is out of range during water heating step…F/06Drive motor tachometer error; control is unable to properly detect motor speed…F/07Motor Control Unit (MCU) error; main control has detected a short in the MCU.F/09Overflow condition; overflow contact on pressure switch is closed for more than…F/10MCU heat sink thermal protector has tripped due to overheating, stopping motor…F/11Serial communication error between the Central Control Unit (CCU) and the Motor…F/13Dispenser system error; dispenser motor cannot be driven to its proper position.F/14EEPROM error; error reading data from the EEPROM onboard the CCU.F/15Motor Control Unit (MCU) error; MCU detects multiple resets or errors during a…F/16CCU/Touchpad LED communication error; the touch-pad/LED assembly cannot…F/20Pressure switch failure; no water detected entering machine or pressure switch…F/21System leak; no water entry detected within 30 seconds or flow sensor detected…F/22Door unlock error; the door cannot be unlocked after 6 attempts.F/24Door lock error; the door cannot be locked after six attempts.F/dlCCU/touch-pad/LED communication error; touch-pad/LED assembly is not able to…F/dUDoor lock error; door cannot be locked after six attempts.F/HNo water detected entering machine or pressure switch trip not detected; valves…F01MCC (Central Control Module) communication errorF11Motor Control Module (MCM) failureF20No water entry detectedF21Excessive drain timeF22Door lock errorF24Water temperature sensor errorF25Tachometer error
View all 48 error codes
F26Door switch errorF27Overflow conditionF28Communication failure between MCC and MCM.F29Motor overheating detected.F30No description availableF31No description availableF33Pump disconnectedF34Load detected in the washer during the washer cleaning cycle.F70Communication failure between MCC and User Interface (UI).F73User Interface (UI) failureF74User Interface (UI) failureFHPressure switch failure; no water entering machine detected within 30 seconds…Memory FailureControl board memory/software failure detected during Field Service Test…Motor high currentMotor drawing excessive current detected during Field Service Test, indicated…Motor low currentMotor drawing insufficient current detected during Field Service Test…SudSuds lock condition detected by MCU analyzing current draw on drive motor; may…Thermistor failureThermistor failure detected during Field Service Test, indicated by Heavy Wash…Turbidity Sensor failureTurbidity sensor failure detected during Field Service Test, indicated by Rinse…

Service modes (19)

  • diagnostic["Ensure washer is empty and control is in OFF state.","Close the door.","Push CONTROL/ON (if…
  • Diagnostic Mode (Blink Mode)["First access Setup/Configuration Mode.","Press DELICATES & KNITS button for 1 second while one of…
  • Diagnostic Test["Ensure washer is empty and control is in the OFF state.","Close the door.","Push CONTROL/ON (if…
  • Diagnostic Test Mode1
  • Field Service TestPress the Heavy Wash key 5 times followed by the Start key within 6 seconds.
  • Help Mode["PD models
  • Last Stored Failure Code Recall1
  • last_stored_failure_code["Select the Drain/Spin cycle.","Select No Spin.","Press and hold the Prewash option button for 5…
  • Manual Function TestPress the Normal Wash key 5 times followed by the Start key within 6 seconds
  • Manual Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WHITES button while the display is blinking."]
  • Quick Drain and Spin["Enter Diagnostic Mode (Blink Mode).","Press COLORS button while the display is blinking."]
  • Quick Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WOOLENS button while the display is blinking."]
  • Retrieve Last Stored Failure Code["Select the Drain/Spin cycle.","Select No Spin.","Press and hold the Prewash option button for 5…
  • Sales Floor Demo ModePress Extra Rinse keypad 5 times within 6 seconds.
  • Setup/Configuration Mode["PD models
  • Washer Cleaning Program["Enter Diagnostic Mode (Blink Mode).","Press BRIGHT button while the display is blinking."]
  • Washer Monthly Maintenance/Cleaning Cycle (Kenmore Elite HE)1
  • Washer Monthly Maintenance/Cleaning Cycle (Whirlpool Duet)1
  • washer_cleaning_cycle["For Kenmore Elite HE

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax