mypros+
Model reference

Amana MRR-1000-P85514-2S

Range

12 documents32 error codes31 service modes

Available documentation

Service Manual

  • Service Manual - SAM002723 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W11696819 - Rev A48 pg
    Covers this model
  • Tech Sheet - W11294668 - Rev A20 pg
    Covers this model

Installation Guide

  • Installation Instructions32 pg
    Covers this model
  • Instrucciones de Instalacion35 pg
    Covers this model
  • Installation Instructions35 pg
    Covers this model
  • Installation Instructions72 pg
    Covers this model
  • Installation Instructions68 pg
    Covers this model
  • Installation Instructions32 pg
    Covers this model
  • Installation Instructions140 pg
    Covers this model
  • Installation Instructions88 pg
    Covers this model
  • Installation Instructions140 pg
    Covers this model
MyPros+ Max

Diagnose your Amana MRR-1000-P85514-2S.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (32)

CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord2Dryer exhaust thermistor open errord22Communication failure from dryer CCU to UICd23Communication failure from UIC to dryer CCUd3Dryer exhaust thermistor shorted errord4Dryer motor control circuit errord5Coin 1 errord6Coin 2 error (dryer)d9Low voltage detection errorF01MCC (Central Control Module) communication errorF03Washer accelerometer failure; X, Y, and Z limits are outside normal range…F04Washer accelerometer failure; X, Y, and Z limits are outside normal range…F11Motor Control Module (MCM) failureF20No water entry detectedF21Excessive drain timeF22Door lock errorF23Dryer exhaust thermistor shorted; temperature above 250°F (<500 Ω) for 1 minute…F24Water temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between MCC and MCM.F29Motor overheating detected.F30Not explicitly described in the extracted text, appears in the error code table…F31Not explicitly described in the extracted text, appears in the error code table…F33Pump disconnectedF34Load detected in the washer during the washer cleaning cycle.F70Communication failure between MCC and User Interface (UI).F71Dryer communication failure from UIC to CCU; CCU is not receiving…
View all 32 error codes
F73User Interface (UI) failureF74User Interface (UI) failure

Service modes (31)

  • Code Display Mode["Can only be accessed when washer is in error state.","PD Models
  • Diagnostic Mode (Blink Mode)["First access Setup/Configuration Mode.","Press DELICATES & KNITS button for 1 second while one of…
  • Flashing Mode["PD Models
  • Help Mode["PD models
  • Help Mode (dAS mode)1
  • Help Mode (PD models)1
  • Manual Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WHITES button while the display is blinking."]
  • P-01 Cancel Cycle, Reset Errors, and Clear Escrow["Enter Service Diagnostic Test Mode.","Display shows P-01.","Press START to clear an active error…
  • P-02 Cycle Credit["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-02 is displayed.","Press START to…
  • P-03 Quick Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-03 is displayed.","Press START to…
  • P-04 Manual Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-04 is displayed.","Press START to…
  • P-05 Button Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-05 is displayed.","Press START to…
  • P-06 Drain and Spin["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-06 is displayed.","Press START to…
  • P-07 UI Diagnostics["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-07 is displayed.","Press START to…
  • P-08 Clean Washer Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-08 is displayed.","Press START to…
  • P-10 Dryer Diagnostic Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-10 is displayed.","Press START to…
  • Quick Drain and Spin["Enter Diagnostic Mode (Blink Mode).","Press COLORS button while the display is blinking."]
  • Quick Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WOOLENS button while the display is blinking."]
  • Service Access Code (free-vend models only)1. Open the door. 2. Within 10 seconds, press in sequence
  • Service Access Code (PN Models without key switch)["Only functions on washers set up for 0 vend price without Special Pricing, and Coin/Debit Option…
  • Service Diagnostic Test Mode["Enter service mode per Control Set-Up Procedures (insert service switch key and turn…
  • Service Diagnostic Test Modes1. Disconnect power and remove service door (PD models) or remove AA1 jumper from IU control board…
  • Set-up Mode["PD/PN/PR Models
  • Setup Mode["PD/PR Models
  • Setup Mode (PD Models)["Insert service access door key, turn, and lift to remove access door.","The washer enters set-up…
  • Setup Mode (PN Models via AA1)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Setup/Configuration Mode["PD models
  • Setup/Configuration Mode (PD models)Insert key into service access door, turn and lift to remove the service access door.
  • Setup/Configuration Mode (PR models)Insert setup card (from card reader manufacturer) into card reader
  • Washer Cleaning Program["Enter Diagnostic Mode (Blink Mode).","Press BRIGHT button while the display is blinking."]
  • Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (setup mode).","Press and hold the QUICK CYCLE button for 1…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass