Model reference

Amana RR-3H

Name: Amana RR-3H
Brand: Amana

Range

3 documents35 error codes17 service modes

Available documentation

Tech Sheet

Tech Sheet - W11696819 - Rev A48 pg
Covers this model
Tech Sheet - W11294668 - Rev A20 pg
Covers this model
Tech Sheet - 160232268 pg
Covers this model

MyPros+ Max

Diagnose your Amana RR-3H.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Range

d13 on my Amana RR-3H

M+

Coin 2 error; blocked coin 2 sensor or

From Tech Sheet W10835473, p.45:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part W10810403

Door lock assembly

Error codes (35)

CodeMeaning

d13Coin 2 error; blocked coin 2 sensor or coin drop UI control circuit failure…d16Generation 2 debit card reader error; not receiving communications from…d2Dryer exhaust thermistor open error d22Communication failure from dryer CCU to UIC d23Communication failure from UIC to dryer CCU d3Dryer exhaust thermistor shorted error d4Dryer motor control circuit error d5Coin 1 error; blocked coin 1 sensor or coin drop UI control circuit failure…d9Low voltage detection error; voltage detected below 90 VAC for 8 seconds.F01Dryer motor control circuit error; control cannot determine if motor relay is…F03Washer accelerometer failure; X, Y, and Z limits are outside normal range…F04Washer accelerometer failure; X, Y, and Z limits are outside normal range…F11Washer MCU error; Motor Control Unit has a failure, possibly repeating under or…F20No water detected entering washer; first level of pressure switch not tripped…F21Long drain; drain time exceeds 8 minutes without reaching reset level in…F22Dryer exhaust thermistor open; temperature drops below 18°F (>50 kΩ) for 1…F23Dryer exhaust thermistor shorted; temperature above 250°F (<500 Ω) for 1 minute…F24Washer water temperature sensor error; sensor value out of range (23°F to 217°F…F25Washer tachometer error; MCU unable to properly detect motor speed.F26Washer door switch error; door switch circuit open for 5 seconds while door is…F27Washer overflow condition; overflow contact on pressure switch closed for more…F28Communication failure between washer CCU and MCU.F29Washer door unlock error; door unable to unlock after six tries.F31Washer motor overheating; MCU heat sink exceeds 212°F (100°C).F33Washer pump disconnected; electrical connection between pump and CCU is lost.F34Load detected in washer during Washer Cleanout Cycle.F70Washer communication failure between CCU and UIC.F71Dryer communication failure from UIC to CCU; CCU is not receiving…F73Dryer UIC microprocessor error; unable to read or verify EEPROM.F74Washer UIC failure; communication error within User Interface Control, possibly…

View all 35 error codes

Memory FailureControl board memory/software failure detected during Field Service Test…Motor high currentMotor drawing excessive current detected during Field Service Test, indicated…Motor low currentMotor drawing insufficient current detected during Field Service Test…Thermistor failureThermistor failure detected during Field Service Test, indicated by Heavy Wash…Turbidity Sensor failureTurbidity sensor failure detected during Field Service Test, indicated by Rinse…

Service modes (17)

Field Service TestPress the Heavy Wash key 5 times followed by the Start key within 6 seconds.
Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
Help Mode (PD Models)["Open the service door.","Press EXTRA RINSE washer keypad until display reads 2.XX.","Press…
Manual Function TestPress the Normal Wash key 5 times followed by the Start key within 6 seconds
P-01 Cancel Cycle, Reset Errors, and Clear Escrow["Enter Service Diagnostic Test Mode.","Display shows P-01.","Press START to clear an active error…
P-02 Cycle Credit["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-02 is displayed.","Press START to…
P-03 Quick Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-03 is displayed.","Press START to…
P-04 Manual Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-04 is displayed.","Press START to…
P-05 Button Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-05 is displayed.","Press START to…
P-06 Drain and Spin["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-06 is displayed.","Press START to…
P-07 UI Diagnostics["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-07 is displayed.","Press START to…
P-08 Clean Washer Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-08 is displayed.","Press START to…
P-10 Dryer Diagnostic Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-10 is displayed.","Press START to…
Sales Floor Demo ModePress Extra Rinse keypad 5 times within 6 seconds.
Service Diagnostic Test Mode["Enter service mode per Control Set-Up Procedures (insert service switch key and turn…
Set-Up Mode["PD/PN/PR Models
Setup Mode["PD/PR Models

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass