mypros+
Model reference

Amana SR22E-P74100-3W

Refrigerator

5 documents79 error codes65 service modes

Available documentation

Tech Sheet

  • tech sheet w10844813 reva20 pg
    Covers this model
  • Tech Sheet5 pg
    Covers this model
  • Tech Sheet2 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 818443020 pg
    Covers this model
  • Instruction Sheet - 816969620 pg
    Covers this model
MyPros+ Max

Diagnose your Amana SR22E-P74100-3W.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (79)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Control software issue10-1Dispenser electrical problem10-2Vent wax motor electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2Damaged or corrupted memory on control board or incompatible software…3-1Thermistor/OWI open3-2Thermistor/OWI shorted3-3OWI failed calibration.4-3Wash motor not running4-3 (cause 2)Control Motor Drive circuit or Sense circuit failure preventing wash motor…5-1Door switch stuck open5-2Door switch stuck closed6-1Inlet water low/no water mechanical problem6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Incoming water too cold (under 84°F/29°C).6-7Flowmeter problem6-8Water softener regeneration valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disc missingd13Coin 2 error
View all 79 error codes
d16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorE0No errors present in the ice maker system.E1Manufacturing codeE2Ice maker errorE3Manufacturing codeE4Manufacturing codeE5Ice maker errorE6Manufacturing codeErManufacturing codeF01CCU errorF03Accelerometer failureF04Accelerometer failureF0E0No error(s) found.F11MCU errorF1E1Internal appliance manager failure.F1E4Microwave ACU PCBA (Appliance Control Unit Printed Circuit Board Assembly)…F20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionsF28Communication failure between CCU and MCU.F29Door unlock errorF2E0Keypad disconnected from user interface.F2E1Stuck key failure on the touch panel.F31Overheating of motorF33Pump disconnectedF34Load detected in washer during washer cleanout cycle.F3E0Main oven sensor open or shorted.F3E1Lower oven sensor open or shorted.F3E2Warming drawer sensor open or shorted.F3E3Meat probe sensor shorted.F4E4Humidity sensor error.F5E0Door switch and latch switch do not agree.F5E1Door latch not operating.F6E0Lost communication between user interface and appliance manager.F6E1Cook range over temperature.F6E2Clean range over temperature.F6E3Mini oven/warm drawer over temperature.F6E4User interface and appliance manager mismatch.F6E5No cavity size command programmed.F70Communication failure between CCU and UI (User Interface).F73UI failureF74UI failureF8E5Exhaust air temperature detection failure.

Service modes (65)

  • Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
  • diagnostic["Plug in microwave oven or reconnect power.","Press CANCEL button to enter Standby mode (colon ':'…
  • Diagnostics Mode["Press the OFF key to place the range in an idle state.","Press the OFF and START keys in the…
  • Help Mode (dAS Mode)Open the service door or insert a manual diagnostic card
  • Help Mode (PD Models)Open the service door
  • Rapid Advance Mode (within Service Diagnostics)While in Service Diagnostics Cycle, press HI TEMP
  • Service Diagnostic Test Modes1
  • Service Diagnostics Cycle1
  • Service Diagnostics Mode["Press SW1 and SW2 simultaneously for 3 seconds.","Release both buttons when you hear the CHIME…
  • Service Diagnostics with Error CodesPress any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second between key presses.
  • Service Test - 38 Forced Defrost ModeWhile in Service Diagnostics Mode, navigate to step 38. Select SW3 to set mode
  • Service Test 1 - FC Thermistor["Enter Service Diagnostics Mode.","Navigate to step 1 (display shows 01).","The board will…
  • Service Test 11 - Dispenser Lighting["Enter Service Diagnostics Mode.","Navigate to step 11.","Pressing SW3 will change the dispenser…
  • Service Test 15 - Ice Level Sensor["Enter Service Diagnostics Mode.","Navigate to step 15.","Displays the Ice Bin Status in real time…
  • Service Test 16 - RC Left Door Switch Input["Enter Service Diagnostics Mode.","Navigate to step 16.","Displays the RC Door status in real time…
  • Service Test 17 - RC Right, Pantries, FC Doors Switch Input["Enter Service Diagnostics Mode.","Navigate to step 17.","Displays the FC Door status in real time…
  • Service Test 18 - Ice Door Motor["Enter Service Diagnostics Mode.","Navigate to step 18.","Press ice paddle and verify that the…
  • Service Test 19 - Ice Maker Fill Tube Heater Status["Enter Service Diagnostics Mode.","Navigate to step 19.","Control the Ice Maker Fill Tube Heater…
  • Service Test 2 - RC Thermistor["Enter Service Diagnostics Mode.","Navigate to step 2.","The board will automatically check the…
  • Service Test 20 - Water Filter Usage Rating["Enter Service Diagnostics Mode.","Navigate to step 20.","Displays in two sequential flashes the…
  • Service Test 21 - Water Filter Time Rating["Enter Service Diagnostics Mode.","Navigate to step 21.","Displays in two sequential flashes the…
  • Service Test 22 - Water Filter Usage["Enter Service Diagnostics Mode.","Navigate to step 22.","Displays in two sequential flashes the…
  • Service Test 23 - Water Filter Time["Enter Service Diagnostics Mode.","Navigate to step 23.","Displays in two sequential flashes the…
  • Service Test 24 - Water Filter Reset["Enter Service Diagnostics Mode.","Navigate to step 24.","Displays in two sequential flashes the…
  • Service Test 26 - Main Control Software Version["Enter Service Diagnostics Mode.","Navigate to step 26.","Displays in three sequential flashes the…
  • Service Test 27 - Dispenser UI Control Software Version["Enter Service Diagnostics Mode.","Navigate to step 27.","Displays in three sequential flashes the…
  • Service Test 29 - Low Voltage IDI Software Version["Enter Service Diagnostics Mode.","Navigate to step 29.","Displays in three sequential flashes the…
  • Service Test 3 - Evaporator Fan Motor and Air Baffle Motor["Enter Service Diagnostics Mode.","Navigate to step 3.","Depress SW3 to cycle
  • Service Test 31 - Touch Input Module Software["Enter Service Diagnostics Mode.","Navigate to step 31.","Displays in three sequential flashes the…
  • Service Test 32 - Ambient Thermistor UI Control["Enter Service Diagnostics Mode.","Navigate to step 32.","Internal board test
  • Service Test 33 - Humidity Sensor UI Control["Enter Service Diagnostics Mode.","Navigate to step 33.","Relative Humidity Test
  • Service Test 34 - Vertical Mullion Heater Mode["Enter Service Diagnostics Mode.","Navigate to step 34.","Set the Vertical Mullion Heater Sensor…
  • Service Test 35 - Vertical Mullion Heater Status["Enter Service Diagnostics Mode.","Navigate to step 35.","Control the Vertical Mullion Heater…
  • Service Test 36 - Ice Box Fan["Enter Service Diagnostics Mode.","Navigate to step 36.","Control Ice Box Fan using SW3
  • Service Test 37 - Ice Box Thermistor["Enter Service Diagnostics Mode.","Navigate to step 37.","The board will check the resistance…
  • Service Test 38 - Forced Defrost Mode["Enter Service Diagnostics Mode.","Navigate to step 38.","Set the Forced Defrost Mode by selecting…
  • Service Test 39 - RC Evap Thermistor["Enter Service Diagnostics Mode.","Navigate to step 39.","The board will check the resistance…
  • Service Test 4 - Compressor/Condenser Fan Motor/Evaporator Fan["Enter Service Diagnostics Mode.","Navigate to step 4.","There will be a delay of 3 seconds before…
  • Service Test 40 - Horizontal Mullion Heater Mode["Enter Service Diagnostics Mode.","Navigate to step 40.","Set the Horizontal Mullion Heater Sensor…
  • Service Test 41 - Horizontal Mullion Heater Status["Enter Service Diagnostics Mode.","Navigate to step 41.","Control the Horizontal Mullion Heater…
  • Service Test 42 - UI EEPROM Control Software Version["Enter Service Diagnostics Mode.","Navigate to step 42.","Displays in three sequential flashes the…
  • Service Test 45 - Ice Maker Water Fill Test["Enter Service Diagnostics Mode.","BEFORE INITIATING THIS TEST, GO TO STEP 57, INITIATE ICE MAKER…
  • Service Test 46 - Water Dispensing Test["Enter Service Diagnostics Mode.","Navigate to step 46.","Press the water pad to initiate a water…
  • Service Test 5 - Compressor Status/Speed["Enter Service Diagnostics Mode.","Navigate to step 5.","Initial Display
  • Service Test 56 - Ice Maker Error Codes["Enter Service Diagnostics Mode.","Navigate to step 56.","Displays active Ice Maker Error Codes on…
  • Service Test 57 - Ice Maker Harvest["Enter Service Diagnostics Mode.","Navigate to step 57.","Press SW3 to activate a Harvest sequence
  • Service Test 58 - Ice Maker Heater Activation and Thermistor["Enter Service Diagnostics Mode.","Navigate to step 58.","Press SW3 to activate the Ice Maker…
  • Service Test 59 - Ice Maker Motor["Enter Service Diagnostics Mode.","Navigate to step 59.","Press SW3 to activate a Motor sequence…
  • Service Test 60 - Pantry UI Software Version["Enter Service Diagnostics Mode.","Navigate to step 60.","Displays in three sequential flashes the…
  • Service Test 63 - All Pantry UI Indicators["Enter Service Diagnostics Mode.","Navigate to step 63.","All pantry LED indicators and pantry UI…
  • Service Test 64 - Pantry UI Button Test["Enter Service Diagnostics Mode.","Navigate to step 64.","Displays the pantry UI Buttons status."]
  • Service Test 65 - Pantry Thermistor["Enter Service Diagnostics Mode.","Navigate to step 65.","The board will check the resistance…
  • Service Test 66 - Manufacturing Codes["Enter Service Diagnostics Mode.","Navigate to step 66.","Displays the active manufacturing error…
  • Service Test 67 - Water Filter Switch Status["Enter Service Diagnostics Mode.","Navigate to step 67.","Displays the water filter switch status…
  • Service Test 73 - Pantry Heater Status["Enter Service Diagnostics Mode.","Navigate to step 73.","Control the Pantry Heater selecting SW3…
  • Service Test 76 - Icebox Fascia Heater["Enter Service Diagnostics Mode.","Navigate to step 76.","Control the Icebox Fascia Heater…
  • Service Test 77 - Defrost Thermistor["Enter Service Diagnostics Mode.","Navigate to step 77.","The board will check the resistance…
  • Service Test 78 - Pantry UI Flashmap Version["Enter Service Diagnostics Mode.","Navigate to step 78.","Displays in three sequential flashes the…
  • Service Test 8 - All UI Indicators["Enter Service Diagnostics Mode.","Navigate to step 8.","All LED indicators and UI display digits…
  • Service Test 80 - LED Driver Software Version["Enter Service Diagnostics Mode.","Navigate to step 80.","Displays in three sequential flashes the…
  • Service Test 81 - LED Driver Flash Software Version["Enter Service Diagnostics Mode.","Navigate to step 81.","Displays in three sequential flashes the…
  • Service Test 9 - UI Button and Pad Test["Enter Service Diagnostics Mode.","Navigate to step 9.","Displays the user Interface Buttons and…
  • Service/Set-up Mode (PD Models)Insert service access door key, turn, and lift to remove service access door
  • Service/Set-up Mode (PR Models)Insert a set-up card (supplied by reader manufacturer) into the card slot
  • Technician Service Access CodeOnly available on washers set to free vend (6 00) with no Special Pricing set-up, and Coin/Debit…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass