Model reference

Amana SR25E-P74100-4W

Name: Amana SR25E-P74100-4W
Brand: Amana

Refrigerator

6 documents62 error codes24 service modes

Available documentation

Tech Sheet

Tech Sheet - W10221852 - Rev A (FR)6 pg
Covers this model
Tech Sheet - W10221845 - Rev A6 pg
Covers this model
Tech Sheet - W10116294A6 pg
Covers this model
Wiring Diagram - W11263829 - Rev A3 pg
Covers this model
Wiring Diagram - W11263829 - Rev B2 pg
Covers this model

Installation Guide

Installation Instructions24 pg
Covers this model

MyPros+ Max

Diagnose your Amana SR25E-P74100-4W.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Refrigerator

E0-F1 on my Amana SR25E-P74100-4W

M+

EEPROM communications failure,

From Tech Sheet W11606106, p.38:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (62)

CodeMeaning

E0-F1EEPROM communications failure, typically caused by power line noise or…E0-F2EEPROM checksum failure, typically caused by power line noise or lightning.E0-F3Key contact closed for more than 60 seconds E0-F5Clean temperature out of range (too high)E1-F1EEPROM communications failure, typically caused by power line noise or…E1-F2EEPROM checksum failure, typically caused by power line noise or lightning.E1-F3Break in oven sensor circuit (open sensor, loosened or disconnected sensor…E1-F5Door switch open during clean cycle E2-F3Short in oven sensor circuit (short in sensor, sensor shorted to casing…E3-F3BAKE/BROIL temperature out of range (too high)F0Default F code F0 E0No error(s) found (Good).F1Electronic control malfunction.F1 E0EEPROM checksum failure.F1 E1EEPROM communications error.F1 E2UL A/D error(s).F1-E0EEPROM communication error.F1-E1Keypad keytail not connected.F1-E2UL A/D error(s).F1-E5Sensor out of range.F1-E6CANCEL key drive line open.F1-E7PCB thermistor open or shorted.F1E0Internal control board failure.F1E1Internal control board failure.F1E2A/D error(s)F2Shorted key on the control panel.F2 E0Shorted key detected.F2 E1Keytail unplugged.F2 E2A/D Error(s).F2-E0Keypad disconnected.

View all 62 error codes

F2-E1Stuck key.F2-E2Cancel key error.F2-E3Oven temp too high F2E0Shorted key (keypad short circuit).F3Oven sensor opened, oven sensor shorted, BAKE/BROIL range over temperature, or…F3 E0Oven sensor opened.F3 E1Oven sensor shorted.F3 E2BAKE/BROIL range over temperature.F3 E3CLEAN range over temperature.F3-E0Main oven sensor open or shorted.F3-E1Self-clean latch will not lock/unlock.F3-E2Warming drawer sensor open or shorted.F3-E3CLEAN range over temperature condition.F3E0Oven sensor F3E1Oven sensor F3E2BAKE/BROIL F3E3CLEAN F5Door latch or switch system failure (related to latch assembly, motor, door…F5 E0Door and switches do not agree.F5 E1Door latch not operating.F5 E2Latch error during CLEAN.F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F5-E2Latch error during CLEAN cycle.F5E0Door and switch mismatch (clean mode).F5E1Door latch not functioning (clean mode).F5E2Door and switch mismatch (clean mode).F6-E1Over temperature during cook mode.F6-E2Over temperature during clean mode.F6-E3Over temperature (warming drawer).F9Miswired house or miswired range.F9E0Miswired house or miswired cooker power supply.

Service modes (24)

Bake Temperature Offset AdjustmentPress BAKE pad for 5 seconds
diagnosticWith the oven not in bake, broil or clean mode, press CANCEL/OFF > CANCEL/OFF > START
Diagnostics ModeWith oven not in cooking, broiling, or cleaning mode, press Cancel/OFF, Cancel/OFF, START. The…
Diagnostics Mode (3-digit LCC 90 and LCC 95 Control Display)Press CANCEL 2 times and then START within a 5-second period.
Diagnostics Mode (Auto Test)1
Diagnostics Test Mode (All LCC Controls)Press CANCEL 2 times and then START within a 5-second period. Then use individual key presses to…
Diagnostics Test Mode (Relay Checks)After entering Diagnostics Mode (CANCEL>CANCEL>START), press individual keys to test relays
DISPLAYPress CANCEL > CANCEL > START to enter Service Mode
ENG MODEPress CANCEL > CANCEL > START to enter Service Mode
Fahrenheit to Celsius ConversionPress the BROIL pad for 5 seconds
FAULTSPress CANCEL > CANCEL > START to enter Service Mode
Last Fault Code RetrievalPress and hold CANCEL/OFF key for 5 seconds to display the last error code.
Manual Diagnostics Mode 1 (Full - within 120 seconds of power up)Within 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then Start
Manual Diagnostics Mode 2 (Limited - after 120 seconds of power up)After 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then Start
Programming Cavity SizeWithin 60 seconds of power up, press the following touchpads in order
Temperature Adjustment1
Temperature Adjustment (All LCC Controls)Step 1
Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds
Temperature Adjustment ModePress and hold BAKE key for 5 seconds
TEST MODEPress CANCEL > CANCEL > START to enter Service Mode
Test Mode / Diagnostic ModeWithin 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds. The…
TEST ON (Relay Checks)Press CANCEL > CANCEL > START to enter Service Mode. Upon entry, 'TEST ON' is displayed. Press the…
USAGEPress CANCEL > CANCEL > START to enter Service Mode
VERSIONPress CANCEL > CANCEL > START to enter Service Mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass