Model reference

Amana TC18D-P73500-25W

Refrigerator

43 error codes6 service modes

MyPros+ Max

Diagnose your Amana TC18D-P73500-25W.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Refrigerator

E0 F0 on my Amana TC18D-P73500-25W

M+

No failure (GOOD) - default state, no

From Tech Sheet W12413655, p.27:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (43)

CodeMeaning

E0 F0No failure (GOOD)E0 F1Check oven user interface E0 F2Keypad disconnected.E0 F3Upper oven sensor shorted or open.E0 F5Door and latch switch do not agree.E0 F6Lost communications between user interface and appliance manager.E1 F1Check oven appliance manager E1 F2Stuck or shorted key on keypad.E1 F3Lower oven sensor shorted or open.E1 F5Door latch not operating.E1 F6Cook oven over temperature.E2 F3Warming drawer sensor shorted or open (oven not equipped with this feature).E2 F6Clean oven over temperature.E3 F3Meat probe shorted.E3 F6Mini oven/warm drawer over temperature (oven not equipped with this feature).E4 F6User interface / appliance manager mismatch.E5 F6No cavity size command programmed in control.F0E0Check oven user interface.F1E1Check oven appliance manager.F1E4Microwave ACU PCBA failure.F2E0Keypad disconnected.F2E1Stuck key / Shorted key.F3E0Main oven sensor open or shorted.F3E1Lower main oven sensor shorted or open.F3E2Warming drawer sensor shorted F3E3Meat probe shorted.F4E4Humidity sensor error.F4E9Smart pop error.F5E0Door and latch switch do not agree.F5E1Door latch not operating.

View all 43 error codes

F6E0Lost communication between user interface and appliance manager.F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E4User interface / appliance manager mismatch.F6E5No cavity size command.F7E0Water is not high enough or water did not boil fast enough.F7E1Boiler over temperature.F7E2Boiler NTC out of range.F7E3Improper filter reset.F7E4Conductivity sensor not connected.F8E0Blower low speed too low.F8E2Blower high speed too low.F8E5Exhaust air temperature detection failure.

Service modes (6)

Diagnostic mode["Press OFF","Press OFF","Press START"]
Diagnostics Mode1. Plug in microwave oven or reconnect power and press CANCEL button to standby (':'). 2. Close…
Diagnostics Mode - Extended ModePress OFF, OFF, START
Model Select / Cavity Size Programming (after User Interface replacement)1
Relay Activation Test1. Enter Diagnostics Menu
Touch Panel and ACU PCBA Diagnostic Test Mode1. Plug in microwave oven or reconnect power and press CANCEL button to standby (colon ':'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass