mypros+
Model reference

Amana TM18J-C-P60178-3WC

Refrigerator

2 documents65 error codes74 service modes

Available documentation

Tech Sheet

  • TechSheet W10918575 RevB32 pg
    Covers this model
  • Tech Sheet - W10730272 - Rev A_W1073027216 pg
    Covers this model
MyPros+ Max

Diagnose your Amana TM18J-C-P60178-3WC.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (65)

CodeMeaning
d 13Coin 2 error; the Coin 2 sensor is detected as blocked for 8 seconds.d 16Generation 2 debit card reader error; no communication from installed debit…d10Communication failure between CCU and UIC.d11MCU errord12Tachometer errord13Coin 2 sensor errord14Overheating of motord15Pump disconnectedd16Generation 2 debit card reader errord17Door lock errord19Door unlock errord2Accelerometer failured20Communication failure between CCU and MCU.d21Overflow conditiond23Load detected in washer during Washer Cleanout Cycle.d24Temperature sensor errord3UIC failured36Stuck key errord4Door switch errord5Coin 1 sensor errord6CCU errord7No water detected entering washer.d8Long draind9Low voltage detection errorF 01Communication error within the Central Control Unit (CCU); the pump drive in…F 04Accelerometer component failed; the X, Y, and Z limits are outside of the…F 11Motor Control Unit (MCU) has a failure, possibly due to a repeating under or…F 20No water detected entering washer; first level of pressure sensor not reached…F 21Long drain; drain time exceeds 8 minutes without reaching reset level in…F 22Door lock error; washer makes several attempts to lock the door and fails after…
View all 65 error codes
F 24Water temperature sensor value is out of range (23°F to 217°F / -5°C to 103°C).F 25Tachometer error; MCU is unable to properly detect motor speed and the washer…F 26Door switch error; the door switch circuit is open for 5 seconds while the door…F 27Overflow condition; the overflow contact on the pressure sensor is closed for…F 28Communication failure between CCU and MCU.F 29Door unlock error; the door is unable to unlock after 6 tries.F 31Overheating of motor; the heat sink exceeds 212°F (100°C)F 33Pump disconnected; the electrical connection between the pump and the CCU is…F 34Load detected in washer during Washer Cleanout Cycle.F 37Water level out of range low; water level has been detected to be below the…F 38Water level out of range high; water level has been detected to be above the…F 70Communication failure between CCU and User Interface (UI).F 73UI failure; communication error within the User Interface, possibly due to a…F 74UI failure (listed as secondary code under F73 section context).F01MCC (Central Control Module) communication errorF03Accelerometer failureF04Accelerometer failureF11Motor Control Module (MCM) failure, possibly due to repeated under-voltage or…F20No water detected entering the washerF21Excessive drain timeF22Door lock errorF24Water temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between MCC (Central Control Module) and MCM (Motor…F29Motor overheating detected by MCM.F31Overheating of motorF33Drain pump disconnectedF34Load detected in washer during the washer cleaning cycle.F37Water level out of range lowF38Water level out of range highF70Communication failure between MCC (Central Control Module) and UI (User…F73UI (User Interface) communication error due to possible power surge or voltage…F74UI (User Interface) communication error due to possible power surge or voltage…

Service modes (74)

  • Code Display Mode["This mode can be accessed only when the washer is in error state.","Open the service door.","The…
  • Code Display Sub-Mode["Open the service door when the washer is in an error state.","The current F code or d code will…
  • Cycle Credit["Enter Flashing Mode (entire display flashing).","Press the HOT button (CC will display)."]
  • Diagnostic - Free Cycle Credit["Enter Blink Mode (entire display flashing).","Press PERM
  • Diagnostic - Manual Overview Test["Enter Blink Mode (entire display flashing).","Press WHITES button."]
  • Diagnostic - Quick Drain and Spin["Enter Blink Mode (entire display flashing).","Press COLORS button."]
  • Diagnostic - Quick Overview Test["Enter Blink Mode (entire display flashing).","Press WOOLENS button."]
  • Diagnostic - Washer Cleaning Program["Enter Blink Mode (entire display flashing).","Press BRIGHTS button."]
  • Diagnostic Mode - Blink Mode["First access Setup Mode.","Press DELICATES AND KNITS for 1 second when setup code 6 is active…
  • Flashing Mode["PD Models
  • Flashing Mode (Diagnostic Sub-Mode)["Open the service door.","Press and hold the COLD button until display segments are…
  • Help Mode["Enter set-up mode.","Press the WARM button until set-up code 2.XX is on display.","Press the HOT…
  • Help Mode (dAS mode)["Open service door or insert manual diagnostic card.","dAS message appears on display.","Press PERM
  • Help Mode (Manual Communication)["Enter set-up mode (open service access door).","Press the WARM button until set-up code 2.XX is…
  • Help Mode (PD models)["Open service door.","Press WOOLENS button until display shows 2.XX.","Press PERM
  • Help Mode (via dAS mode)["Enter set-up mode.","The message dAS will appear in the display.","Press the HOT button.","Press…
  • Help Mode (via Manual Communication)["Enter set-up mode.","Press the WARM button until the set-up code 2.XX is on display.","Press the…
  • Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the COTTON/WHITES button."]
  • Manual Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WHITES button to start the…
  • P-01 Cancel Cycle, Reset Errors, and Clear EscrowFrom Service Diagnostic Test Modes, navigate to P-01 display and press START
  • P-01: Cancel Program, Error Reset, Clear Stored Credit["Enter Service Diagnostic Test Modes (steps 1-3).","Press START when 'P-01' is displayed."]
  • P-02 Cycle CreditFrom Service Diagnostic Test Modes, navigate to P-02 display and press START.
  • P-02: Program Credit["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-02 using LOWER CENTER…
  • P-03 Quick Overview TestFrom Service Diagnostic Test Modes, navigate to P-03 display and press START.
  • P-03: Quick Overview Test Program["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-03 using LOWER CENTER…
  • P-04 Manual Overview TestFrom Service Diagnostic Test Modes, navigate to P-04 display and press START.
  • P-04: Manual Overview Test Program["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-04 using LOWER CENTER…
  • P-05 Button TestFrom Service Diagnostic Test Modes, navigate to P-05 display and press START
  • P-05: Button Test["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-05 using LOWER CENTER…
  • P-06 Drain and SpinFrom Service Diagnostic Test Modes, navigate to P-06 display and press START.
  • P-06: Drain and Spin["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-06 using LOWER CENTER…
  • P-07 UI DiagnosticsFrom Service Diagnostic Test Modes, navigate to P-07 display and press START
  • P-07: UI Diagnostics["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-07 using LOWER CENTER…
  • P-08 Clean Washer CycleFrom Service Diagnostic Test Modes, navigate to P-08 display and press START.
  • P-08: Washer Clean Cycle["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-08 using LOWER CENTER…
  • P-09 Factory DiagnosticsFrom Service Diagnostic Test Modes, navigate to P-09 display and press START.
  • P-09: Factory Diagnostics["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-09 using LOWER CENTER…
  • Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the WARM button."]
  • Quick Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WOOLENS button to start the…
  • Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the PERM PRESS button."]
  • Service Access Code1
  • Service Access Code (alternate setup entry without removing console)["If the washer is not in failure mode, open the door.","Press the upper left button.","Press the…
  • Service Access Code (free-vend models only)1. Open the door. 2. Within 10 seconds, press in sequence
  • Service Access Code (key dance entry without console removal)["Washer must be set for 0 vend price, no Special Pricing, and Coin/Debit Option set to…
  • Service Access Code (key dance)["Only available on washers set to free vend (6 00) with no Special Pricing set-up and Coin/Debit…
  • Service Access Code (no console removal)["Open the door.","Press the upper left key pad.","Press the lower right key pad.","Press the upper…
  • Service Access Code (PN Models - keyless entry)["Only functions on washers set up for 0 vend price without any Special Pricing, and Coin/Debit…
  • Service Access Code (PR models configured as PN, no key switch)["Using only the three bottom buttons (numbered 1, 2, 3 from left to right):","1. Press button 2…
  • Service Access Code (Technician Entry)["This method is only available on washers set for free operation (code 6 00).","Open the…
  • Service Access Code (Technician)Only works on washers set to free vend (6 00) without Special Pricing, Coin/Debit Option must be…
  • Service Diagnostic Test Modes["Make sure power is turned off, then remove the service door on metercase models, or remove the…
  • Service/Set-up Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door.","The washer enters…
  • Service/Set-up Mode (PR Models with set-up card)["Insert a set-up card (supplied by the reader manufacturer) into the card slot."]
  • Service/Set-up Mode (via service connector removal)["Unplug washer or disconnect power.","Open console, disconnect plug on service connector, close…
  • Service/Setup Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door.","The washer enters…
  • Service/Setup Mode (PR Models via AA1 jumper)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1 connector on circuit…
  • Service/Setup Mode (PR Models)Insert a set-up card (supplied by reader manufacturer) into the card slot. If no set-up card is…
  • Set-Up Mode (9150 Models)["Insert access door key, turn, and lift to remove access door."]
  • Set-Up Mode (9160 Models via AA1 connector)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Set-Up Mode (9160 Models)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Set-Up Mode (COIN models)Insert access door key, turn, and lift to remove access door
  • Set-Up Mode (NON-COIN models via service connector)1
  • Set-up Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door.","Use the lower…
  • Set-up Mode (PR Models)["Once the debit card reader is installed, insert a set-up card (supplied by the reader…
  • Setup Mode["Insert access door key, turn, and lift to remove access door.","Alternatively, if a debit card…
  • Setup Mode (PD models)["Insert key into service access door.","Turn and lift to remove the service access door.","Use…
  • Setup Mode (PN Models - AA1 method)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Setup Mode (PR models via AA1 connector)["Disconnect washer from power.","Open console, disconnect connector AA1 from UI board.","Close…
  • Setup Mode (PR Models via AA1 jumper removal)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1 connector on circuit…
  • Setup/Configuration Mode (PD models)["Insert the service door access key, turn and lift to remove the service access door."]
  • Setup/Configuration Mode (PR models)["Insert the setup card (provided by card reader manufacturer) into the card reader.","If no setup…
  • Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the COLORS/DELICATES button."]
  • Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (setup mode).","Press and hold the COLD button for 2 seconds…
  • Washer Diagnostic Mode (Flashing Mode)["Enter Setup Mode (open service access door or insert set-up card).","Press and hold the COLD…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass