Model reference

Amana TR18D-P73500-23W

Name: Amana TR18D-P73500-23W
Brand: Amana

Refrigerator

2 documents35 error codes17 service modes

Available documentation

Installation Guide

Instrucciones de instalación11 pg
Covers this model

Quick Reference

Quick Reference Guide24 pg
Covers this model

MyPros+ Max

Diagnose your Amana TR18D-P73500-23W.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Refrigerator

d 13 on my Amana TR18D-P73500-23W

M+

Coin 2 error; the Coin 2 sensor is

From Tech Sheet W14113048, p.20:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part W10810403

Door lock assembly

Error codes (35)

CodeMeaning

d 13Coin 2 error; the Coin 2 sensor is detected as blocked for 8 seconds.d 16Generation 2 debit card reader error; no communication from installed debit…d5Coin 1 error; the Coin 1 sensor is detected as blocked for 8 seconds.d9Low voltage detection error; incoming voltage detected below 90 VAC for 8…F 01Communication error within the Central Control Unit (CCU); the pump drive in…F 04Accelerometer component failed; the X, Y, and Z limits are outside of the…F 11Motor Control Unit (MCU) has a failure, possibly due to a repeating under or…F 20No water detected entering washer; first level of pressure sensor not reached…F 21Long drain; drain time exceeds 8 minutes without reaching reset level in…F 22Door lock error; washer makes several attempts to lock the door and fails after…F 24Water temperature sensor value is out of range (23°F to 217°F / -5°C to 103°C).F 25Tachometer error; MCU is unable to properly detect motor speed and the washer…F 26Door switch error; the door switch circuit is open for 5 seconds while the door…F 27Overflow condition; the overflow contact on the pressure sensor is closed for…F 28Communication failure between CCU and MCU.F 29Door unlock error; the door is unable to unlock after 6 tries.F 31Overheating of motor; the heat sink exceeds 212°F (100°C)F 33Pump disconnected; the electrical connection between the pump and the CCU is…F 34Load detected in washer during Washer Cleanout Cycle.F 37Water level out of range low; water level has been detected to be below the…F 38Water level out of range high; water level has been detected to be above the…F 70Communication failure between CCU and User Interface (UI).F 73UI failure; communication error within the User Interface, possibly due to a…F 74UI failure (listed as secondary code under F73 section context).F0No error present.F10Display error.F2KKey or foil pressed more than 1 minute.F2TTouch panel pressed more than 1 minute.F3HHumidity sensor out of range.F3TTemperature sensor out of range.

View all 35 error codes

F7Power to magnetron interrupted.F9CE2PROM CheckSum error.F9EE2PROM empty.F9ME2PROM missing.F9WE2PROM write error.

Service modes (17)

Help Mode (dAS Mode)1
Help Mode (PD Models)1
P-01 Cancel Cycle, Reset Errors, and Clear EscrowFrom Service Diagnostic Test Modes, navigate to P-01 display and press START
P-02 Cycle CreditFrom Service Diagnostic Test Modes, navigate to P-02 display and press START.
P-03 Quick Overview TestFrom Service Diagnostic Test Modes, navigate to P-03 display and press START.
P-04 Manual Overview TestFrom Service Diagnostic Test Modes, navigate to P-04 display and press START.
P-05 Button TestFrom Service Diagnostic Test Modes, navigate to P-05 display and press START
P-06 Drain and SpinFrom Service Diagnostic Test Modes, navigate to P-06 display and press START.
P-07 UI DiagnosticsFrom Service Diagnostic Test Modes, navigate to P-07 display and press START
P-08 Clean Washer CycleFrom Service Diagnostic Test Modes, navigate to P-08 display and press START.
P-09 Factory DiagnosticsFrom Service Diagnostic Test Modes, navigate to P-09 display and press START.
Service Access Code1
Service Diagnostic Test Modes1
Set-Up Mode (COIN models)Insert access door key, turn, and lift to remove access door
Set-Up Mode (NON-COIN models via service connector)1
Touch Panel and Microcomputer Board Test (Self-Diagnostic)["Press the clock key.","Press keys 1, 2, and 3 on the keyboard.","Touch AM/PM on the touch screen…
Touch Panel and Microcomputer Board Test Mode (Self-Diagnostic)["Press the CLOCK key.","Touch 'Hours' on the touch screen and set hours to '1'.","Touch 'Minutes'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass