Model reference
Amana NFW5800HW4
Washer
16 documents29 error codes5 service modes
Available documentation
Tech Sheet
- Service Technician Technical Sheet W11417642E2 pg
- Tech Sheet - W11417642 - Rev G2 pg
- Error Codes / Codes d'Anomalies2 pg
- Service Technical Sheet W1115698956 pg
- Tech Sheet W11156989 RevA60 pg
Service Manual
- Service Manual Whirlpool & Maytag 27" Front-load Washers94 pg
Wiring Diagram
- Wiring Sheet W112437161 pg
Service Flash
- Technical Service Pointer6 pg
- Technical Service Pointer - Moisture in Ventilation Tube3 pg
- 27" Front Load Washer Unresponsive Unit6 pg
- Technical Service Pointer6 pg
- Technical Service Pointer3 pg
- Technical Service Pointer #W11025472 - Front Load Direct Drive Washers Dispenser Discoloration/Residue3 pg
Quick Reference
- Quick Reference Guide2 pg
Other
- Service Pointer - W11616794 - Rev A - Front Load Washers Tub Ventilation Change_W116167946 pg
Installation Guide
- Installation Pointer - W10608624 - Drain Hose Installation6 pg
MyPros+ Max
Diagnose your Amana NFW5800HW4.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (29)
CodeMeaning
F0E1Load detected in drum during Clean Washer cycle.F0E2Oversuds condition detected.F0E4High temperature error during wash cycle.F0E5Off balance load detected.F1E1Main relay open or shorted.F1E2MCU over-voltage or under-voltage error.F3E1Wash NTC open or shorted.F3E2Wash NTC (thermistor) open or shorted.F3E5Dry NTC fault.F3E6Accelerometer error.F4E1Wash heater relay error or no feedback signal.F4E2Wash heater relay error.F4E4Blower error.F5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6E1No communication from the HMI detected by ACU.F6E2No communication from the ACU detected by the HMI.F6E3No communication from the MCU detected by the ACU.F7E10Motor disconnected error (also displayed as F7EA).F7E12MC/MCU overload (also displayed as F7EC).F7E2MC/MCU over temperature error.F7E8MC/Motor over temperature error.F7E9Motor will not turn (locked rotor).F7EAMotor disconnected error (alternate display of F7E10).F7ECMC/MCU overload (alternate display of F7E12).F8E1Long fill condition (also displayed as Lo Flo).F8E3Overflow condition detected.F9E1Long drain condition.Service modes (5)
- Fault/Error Code Display["Activate Service Diagnostic Mode; the most recent fault code is shown immediately upon…
- Human-Machine Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
- Quick Diagnostic Test["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
- Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","After initial power is…
- Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana washer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass