mypros+
Model reference

Amana NTW4651BQ0

Washer

4 documents22 error codes9 service modes

Available documentation

Tech Sheet

  • w10468340 tech sheetpdf wtw4900aw048 pg
    Covers this model
  • TechSheet W10468340 RevC48 pg
    Covers this model
  • Kenmore Whirlpool Modular Washer 110 21302013 Tech Sheet48 pg
    Covers this model

Installation Guide

  • Instrucciones de instalación10 pg
    Covers this model
MyPros+ Max

Diagnose your Amana NTW4651BQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected during cycle.F1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and User Interface identification; UI ID does not…F3E1Pressure system fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor is detected to be open or…F5E1Lid switch fault; lid is in locked state but lid switch is open, control not…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed fault; main control cannot determine speed of basket, or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill or long fill; water level does not change for a period of time OR water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (9)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' LED is On.","Press…
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' LED is On.","Press…
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Done' LED is On.","Press…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin & Done' LEDs are…
  • Service Diagnostic Test Mode Entry["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse, Spin, and Done'…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash and Done' LEDs are…
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse & Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass