Model reference

Amana TWA-200/P75753-1W

Washer

7 documents42 error codes6 service modes

Available documentation

Tech Sheet

Tech Sheet - W10268745 - Rev A10 pg
Covers this model
Tech Sheet - W10918869 Rev E6 pg
Covers this model

Quick Reference

Quick Reference Sheet40 pg
Covers this model
Quick Reference Manual1 pg
Covers this model

Installation Guide

Instrucciones de instalacion22 pg
Covers this model
Instrucciones de instalacion22 pg
Covers this model
Instruction Sheet2 pg
Covers this model

MyPros+ Max

Diagnose your Amana TWA-200/P75753-1W.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Amana Washer

: on my Amana TWA-200/P75753-1W

M+

Flashing colon indicates a power

From Tech Sheet W14806940, p.32:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (42)

CodeMeaning

:Flashing colon indicates a power failure has occurred.1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory or control board, incompatible software components…10-1Dispenser electrical problem 10-3Drying fan error 2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control 3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection or…3-3OWI (optical soil sensor) calibration failure.4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…5-1Door stuck open 5-2Door stuck closed 6-1Inlet water low/no water (mechanical problem)6-2Inlet water fill valve electrical problem 6-3Suds/air in pump 6-4Float switch open 6-6Incoming water cool 6-8Regen valve electrical problem 7-1No heat 7-1 (flowmeter)Disconnected or damaged flowmeter.7-2Heater stuck on 8-1Slow drain 8-2Drain motor electrical problem 8-3Drain motor stuck on 8-5Drain stuck on 9-1Diverter can't find position 9-2Diverter stuck on 9-3Diverter disk missing F2Touch panel failure.

View all 42 error codes

F3E0Refrigerator/Main compartment (Z1) thermistor short or open circuit.F3E1Freezer/Main compartment (Z1) thermistor short or open circuit.F3E2Refrigerator Evaporator thermistor short or open circuit.F3E3Freezer Evaporator thermistor short or open circuit.F3E4Deli compartment (Z2) thermistor short or open circuit.F3E5Crisper (Z3) thermistor short or open circuit.F3HHumidity sensor failure.F6MW relay (Relay 4903) failure FDE0Ice maker tray thermistor short or open circuit.FDEAIce Maker Jammed (cannot find Homing or end of harvest location).OPOpen circuit detected on thermistor.SHShort circuit detected on thermistor.

Service modes (6)

Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
Self-Diagnostic / Test Mode["Press and hold the CANCEL/OFF button while opening the door.","While still holding the CANCEL/OFF…
Service Diagnostics Cycle1
Service Diagnostics Mode["Press the pulsing JennAir logo to wake up the UI.","Press the middle zone key.","Press CONNECT…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass