mypros+
Model reference

Caloric RSS352-OF

Range

5 documents32 error codes7 service modes

Available documentation

Service Manual

  • Service Manual - RC231002124 pg
    Covers this model

Tech Sheet

  • TECH SHEET - 9754365 - Rev A8 pg
    Covers this model
  • Tech Sheet 97543654 pg
    Covers this model
  • TECH SHEET - KitchenAid Range KESH307HBS68 pg
    Covers this model

Installation Guide

  • Installation Instructions32 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric RSS352-OF.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (32)

CodeMeaning
F0 E0No fault found.F1Indicates a failed component in the Electronic Range Control (ERC).F1 E2Lost communication with power board.F1 E3Configuration jumper change; freestand, electric switches or P3 pins 1 to 5…F1 E4Oven sensor not calibrated.F1 E5Meat probe not calibrated.F1 E6Display board EPROM access failure.F1 E7Power board EPROM access failure.F1 E8Improper keypad feedback from power board supply lift.F1 E9Unstable keyboard gain.F1 EAExceeded stack warning level.F2Sensor resistance too high.F2 E0User is cleaning too long or keypad is disconnected.F2 E1Cancel key invalid.F2 E3Key held down too long or keyboard short or spill on switch surface.F3Open wire lead in sensor harness, bad harness/sensor connection, or sensor…F3 E0Oven sensor open circuit.F3 E3Shorted oven sensor.F3 E4Oven temperature too high (runaway condition).F4Sensor resistance too low (below 500 ohms).F4 E0Meat probe shorted (less than 1500 ohms).F5Indicates a failed component in the ERC.F5 E1Self clean latch not locking.F5 E5Self clean temperature not achieved after 30 minutes.F5 E7Door unlocked but will not unlatch during clean cycle.F6Indicates a failed component in the ERC or caused by fluctuations in 60 Hz…F7Indicates a shorted or sticking contact in one or more of the function control…F7 E0Invalid latch switch reading.F7 E1Invalid door switch reading.F8Indicates a failed component in the ERC.
View all 32 error codes
F9Door Latch Supervisory failurePFPower failure occurred (not a failure mode).

Service modes (7)

  • Display Test / Sales Demonstration Mode (One Piece ERC)["Clock must previously be set for the time of day.","Press and hold the CLOCK button until TIME is…
  • Display Test / Sales Demonstration Mode (Two Piece ERC)["Clock must previously be set for the time of day.","Press and hold the CLOCK button until TIME is…
  • End of Service Test Sequence (Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • End of Service Test Sequence (Non-Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • ERC Temperature Calibration Mode (One Piece Control)["Press and release the BAKE TEMP function button.","Rotate the TIME/TEMP SET knob clockwise until…
  • ERC Temperature Calibration Mode (Two Piece Control)["Press and release the BAKE TEMP function button.","Rotate the TIME/TEMP SET knob clockwise until…
  • Military Time Toggle (Slide In Clock/Timer)["Simultaneously press COOK/CLEAN TIME button and STOP TIME button to toggle between standard AM/PM…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass