Model reference
Electrolux FFU1464FW
Freezer
3 documents68 error codes13 service modes
Available documentation
Service Manual
- Frigidaire 2006 Service Pointers139 pg
- Upright Freezer Service Manual7 pg
Training
- Technical Service Manual 2006 Technical Training Manual139 pg
MyPros+ Max
Diagnose your Electrolux FFU1464FW.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (68)
CodeMeaning
CEDishwasherCLDishwasherE10Dryer: General EEPROM faultE11Dryer: Checksum errorE12Dryer: Non-fatal R/W errorE13Water leak in tub or air leak in air bell.E21Water not pumping out fast enough.E23Drain pump relay on control board failed or wire off pump.E24Dryer: Control NTC short circuitE25Dryer: Control NTC open circuitE31Pressure sensor not communicating with control board.E35Pressure sensor indicates water overfill.E36Control board problem.E41Control board thinks the door switch is open.E43Control board problem.E44Control board problem.E45Control board problem.E46Control board problem.E47Board thinks the door PTC circuit is open in spin.E48Board thinks the door PTC circuit is closed.E4ADryer: Program timeout faultE52Bad signal from tacho generator.E56High motor current.E57High current on inverter.E58High current on motor phase.E59No tacho signal for 3 seconds.E5AHigh temperature on heat sink caused by overloading.E5BHigh temperature on heat sink.E5CHigh temperature on heat sink.E5DCommunication problem between control board and speed control board.View all 68 error codes
E5ECommunication problem between control board and speed control board.E5FCommunication problem between control board and speed control board.E66Heating element relay failure.E67Input voltage on microprocessor incorrect.E68Dryer: Key (button) stuck faultE70The control board is not seeing the correct water supply.E71Wash NTC failure (tub heater).E74Wash temperature does not increase.E75Water temperature sensor circuit failure.E76NTC temperature for the cold water valve over the limits; hot and cold water…E82Console control problem.E83Console control problem.E8CDryerE91Communication error between UI board and control board.E93Console control problem.E94Console control problem.E95Communication error.E97Console control problem.E98Console control problem.E9EDryerEAFDryer: Watchdog resetEB1Incoming power frequency out of limits.EB2Incoming line voltage above 130 VAC.EB3Incoming line voltage below 90 VAC.EBEConsole control problem.EBFConsole control problem.EF1Clogged drain pump.EF2Too much soap.EF5NTC temperature for the hot water valve over the limits; hot and cold water…ErDishwasher: Membrane switch failureHODishwasher: Heat delayhsDishwasherLODishwasherPFDishwasherrADishwasheruFDishwasherULDishwasheruoDishwasher
Service modes (13)
- Affinity Dryer Error Code Access (Field Test Mode)["Press and hold the Select and Cancel buttons simultaneously for 6 seconds to reset control
- Affinity Dryer Function Test Sequence["Press and hold Select and Cancel buttons simultaneously for 6 seconds to reset the control
- Dishwasher Relay/Triac and Sensor Test["Unit must be in PF (Power Failure) condition
- Dishwasher Water Temperature Test["At idle
- Dishwasher Water/Service Test["From an idle condition (no programs entered), press pad #9 and START/CANCEL (pad #11)…
- Electronic Freezer Diagnostic Mode (GLFU/FFU/Kenmore Elite)["Adjust the temperature setting to 0°F using UP ARROW and DOWN ARROW buttons.","Press and hold…
- Electronic Freezer Diagnostics Mode (Single Digit Display)["Set the cold control at position 4.","Depress the 'Alarm off' and 'Quick Freeze' buttons for 6…
- Electronic Freezer Manual Defrost (GLFU/FFU/Kenmore Elite)["Press and hold the QUICK FREEZE and ALARM RESET buttons until the UI beeps once and displays…
- Electronic Freezer Manual Defrost (Low-End Electronics 216554170 etc.)["Set control to '2'.","Hold both buttons down for a couple of seconds.","A 'd' is displayed while…
- Electronic Freezer Service Mode (Low-End Electronics 216554170 etc.)["Set control to setting '4'.","Hold both buttons for a couple of seconds.","Control enters Service…
- Front Load Washer Clear Stored Error Codes["Turn the Program Knob to the start position (Spin Only).","Press Start/Pause to start the cycle…
- Front Load Washer Diagnostic Mode["Turn the Program Knob to the start position (Spin Only).","Press Start/Pause to start the cycle…
- Front Load Washer Error Code Reading["Wake the washer by pressing any button.","Wait 5 seconds.","Press and HOLD the Start/Pause and…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux freezer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass