Model reference

GE PDW9900N00BB

Name: GE PDW9900N00BB
Brand: GE

Dishwasher

6 documents2 error codes17 service modes

Available documentation

Service Manual

GE Profile Dishwasher Technical Service Guide37 pg
Covers this model
GE Consumer & Industrial Technical Service Guide - GE Profile Dishwasher PDW8900 Series, PDW9700 Series, PDW9900 Series37 pg
Covers this model
GE Profile TM Dishwasher Technical Service Guide37 pg
Covers this model
GE Profile Dishwashers Owner's Manual48 pg
Covers this model

Other

PDW8680NSSowner48 pg
Covers this model
cdw9380owne48 pg
Covers this model

MyPros+ Max

Diagnose your GE PDW9900N00BB.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·GE Dishwasher

Lock LED + continuous beep on my GE PDW9900N00BB

M+

Factory Test Mode calibration failure:

From Service Manual 577059, p.31:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WR55X10025

Temperature sensor

Error codes (2)

CodeMeaning

Lock LED + continuous beepFactory Test Mode calibration failure Sensing LED not litTurbidity sensor circuit has failed open or is shorted; unit will operate for…

Service modes (17)

Consumer Purge Cycle1. Make sure Pre-wash, Added Heat, and Heated Dry LEDs are off. 2. Press Heated Dry and Cookware…
Control Panel Lock/Unlock["Press and hold the HEATED DRY pad for 3 seconds to lock the controls (light above LOCK pad will…
Demo ModePress the Cookware pad (Down arrow on Top Control models) and Added Heat pad simultaneously for 5…
Factory Test Mode1
Service ModePDW8900 Series
SmartDispense Water Hardness Calibration (12-Button Front-Control Models With 3-Digit Display)["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
SmartDispense Water Hardness Calibration (7-Button Front-Control Models With 3-Digit Display)["Open the door and touch a pad (other than START) to turn lights on.","Press the Up Arrow Pad and…
SmartDispense Water Hardness Calibration (Models Without a 3-Digit Display - Front Controls)["Close and latch the door (lights on, dishwasher not running).","Press the COOKWARE and DELAY…
SmartDispense Water Hardness Calibration (Models Without a 3-Digit Display - Top Controls)["Open the door and touch a pad to turn lights on.","Press the Up Arrow Pad and DELAY HOURS pad at…
Toggle End-of-Cycle Audible Signal["Press the HEATED DRY pad 5 times within 3 seconds.","A triple beep will sound to indicate the…
Toggle LOW DETERGENT LED (when not using SmartDispense)["Press the ADDED HEAT pad 5 times within 3 seconds.","You will hear 3 beeps; then the light will…
Turbidity Sensor CalibrationMust be entered within 2 minutes of power up
Water Hardness Calibration ModePDW8900
Water Hardness Calibration Mode - Front Mount Control (PDW8900)["Dishwasher must be in standby mode
Water Hardness Calibration Mode - Top Mount Control (PDW9700, PDW9900)["Dishwasher must be in standby mode.","Press up arrow to wake up control and illuminate the lights…
Water Hardness Calibration Mode (PDW8900)Dishwasher must be in standby mode
Water Hardness Calibration Mode (PDW9700/PDW9900)Dishwasher must be in standby mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass