Model reference

GE ZDOD240P

Name: GE ZDOD240P
Brand: GE

Refrigerator

3 documents2 error codes26 service modes

Available documentation

Service Manual

TECHNICAL SERVICE GUIDE - Double-Drawer, Outdoor/Indoor, Fresh-Food, Beverage Center, and Wine Reserve Refrigerators26 pg
Covers this model
GUÍA TÉCNICA DE SERVICIO - Refrigeradores de Gaveta-Doble, Exterior/Interior, Enfriador, Centro de Bebidas y Reserva de Vinos25 pg
Covers this model

Bulletin

Monogram Outdoor/Indoor Refrigerators - Moisture shorts out control board2 pg
Covers this model

MyPros+ Max

Diagnose your GE ZDOD240P.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·GE Refrigerator

bAd on my GE ZDOD240P

M+

Thermistor is electrically open or

From Service Manual 319137, p.29:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WR55X10025

Temperature sensor

Error codes (2)

CodeMeaning

bAdThermistor is electrically open or shorted, displayed during diagnostic mode 07…JPSJumper in J4 position was not removed from the replacement power supply board…

Service modes (26)

Diagnostic 01 - Showroom ModeEnter Service Mode, navigate to diagnostic 01 using A/B buttons, press D to enter.
Diagnostic 02 - Communication Data CheckEnter Service Mode, navigate to diagnostic 02 using A/B buttons, press D to enter.
Diagnostic 06 - Display TestEnter Service Mode, navigate to diagnostic 06 using A/B buttons, press D to enter.
Diagnostic 07 - Sensor System TestEnter Service Mode, navigate to diagnostic 07 using A/B buttons, press D to enter.
Diagnostic 10 - Damper Test (Bar Unit only)Enter Service Mode, navigate to diagnostic 10 using A/B buttons, press D to enter.
Diagnostic 12 - 100% Run Time TestEnter Service Mode, navigate to diagnostic 12 using A/B buttons, press D to enter.
Diagnostic 14 - Defrost Heater and Fill Tube Test (Bar Unit only)Enter Service Mode, navigate to diagnostic 14 using A/B buttons, press D to enter.
Diagnostic 15 - ResetEnter Service Mode, navigate to diagnostic 15 using A/B buttons, press D to enter.
Diagnostic 16 - Exit Diagnostic ModeEnter Service Mode, navigate to diagnostic 16 using A/B buttons, press D to enter.
Diagnostic 21 - Reed Switch TestEnter Service Mode, navigate to diagnostic 21 using A/B buttons, press D to enter.
Diagnostic 22 - Light Circuit TestEnter Service Mode, navigate to diagnostic 22 using A/B buttons, press D to enter.
Diagnostic Mode 01 - Showroom ModeEnter Service Mode, use keypad A to increase or keypad B to decrease until diagnostic mode 01 is…
Diagnostic Mode 02 - Data Communication CheckEnter Service Mode, select diagnostic mode 02 using keypad A/B, press keypad D to enter.
Diagnostic Mode 06 - Display TestEnter Service Mode, select diagnostic mode 06 using keypad A/B, press keypad D to enter.
Diagnostic Mode 07 - Sensor System TestEnter Service Mode, select diagnostic mode 07 using keypad A/B, press keypad D to enter.
Diagnostic Mode 10 - Damper Test (Bar unit only)Enter Service Mode, select diagnostic mode 10 using keypad A/B, press keypad D to enter.
Diagnostic Mode 12 - 100% Run TimeEnter Service Mode, select diagnostic mode 12 using keypad A/B, press keypad D to enter.
Diagnostic Mode 14 - Defrost and Fill Tube Heater (Bar unit only)Enter Service Mode, select diagnostic mode 14 using keypad A/B, press keypad D to enter.
Diagnostic Mode 15 - ResetEnter Service Mode, select diagnostic mode 15 using keypad A/B, press keypad D to enter.
Diagnostic Mode 16 - Exit Diagnostic ModeEnter Service Mode, select diagnostic mode 16 using keypad A/B, press keypad D to enter.
Diagnostic Mode 21 - Switch (Reed) TestEnter Service Mode, select diagnostic mode 21 using keypad A/B, press keypad D to enter.
Diagnostic Mode 22 - LightsEnter Service Mode, select diagnostic mode 22 using keypad A/B, press keypad D to enter.
Diagnostic Mode 23 - DC Fresh-Food FanEnter Service Mode, select diagnostic mode 23 using keypad A/B, press keypad D to enter.
Diagnostic Mode 24 - Delay for Evaporator Fan and Damper after Defrost (Bar unit only)Enter Service Mode, select diagnostic mode 24 using keypad A/B, press keypad D to enter.
Diagnostic Mode 93 - OffsetEnter Service Mode, select diagnostic mode 93 using keypad A/B, press keypad D to enter.
Service ModePress keypads A, B, and D simultaneously for 5 seconds.

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass