Model reference

Ikea YWFI910H0AS0

Range

10 documents40 error codes14 service modes

Available documentation

Tech Sheet

Fiche technique - Tech Sheet W104413076 pg
Covers this model
Tech Sheet - W10392955 - Rev A (MRC-FR)8 pg
Covers this model
Tech Sheet - W10441306 - Rev A6 pg
Covers this model
Tech Sheet - W10392954 - Rev A (MRC)8 pg
Covers this model

Service Flash

Technical Service Pointer10 pg
Covers this model

Tech Tip

Instruction Sheet2 pg
Covers this model
Oven Cleaning Quick Reference Guide2 pg
Covers this model

Installation Guide

Installation Instructions16 pg
Covers this model
Instruction Sheet2 pg
Covers this model

Quick Reference

Quick Reference Manual2 pg
Covers this model

MyPros+ Max

Diagnose your Ikea YWFI910H0AS0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Ikea Range

C-81 on my Ikea YWFI910H0AS0

M+

Over temperature condition detected.

From Service Manual 157148, p.40:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (40)

CodeMeaning

C-81Over temperature condition detected.C-82Over temperature condition detected.F-12Coil under current detected on a burner.F-21Supply power frequency is incorrect.F-25Stuck fan on power control board (right or left side fan, depending on which…F-36Temperature sensor is not working.F-37Temperature sensor is not working.F-40Power control board failure.F-42Power supply issue detected.F-47Power supply from power control board to User Interface is missing, or WIDE…F-56Wrong or invalid configuration (User Interface).F-58Wrong or invalid configuration (power control board).F-60User Interface does not work.F-61Power control board does not work.F1 E0EEPROM communication error.F1 E5Sensor out of range.F1 E7Board thermistor open or shorted.F1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7PCB thermistor open or shorted.F2 E0Keypad disconnected.F2 E1Stuck key.F2 E2Cancel key error.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F3 E0Main oven sensor open or shorted.F3 E2Warming drawer sensor open or shorted.F3-E0Main oven sensor open or shorted.F3-E2Warming drawer sensor open or shorted.

View all 40 error codes

F5 E0Door and switch mismatch (clean mode).F5 E1Door latch not functional (clean mode).F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F6 E1Bake F6 E2Clean F6 E3Warming drawer F6-E1Over temperature during cook mode.F6-E2Over temperature during clean mode.F6-E3Over temperature in warming drawer.

Service modes (14)

Auto TestEnter diagnostic mode (CANCEL>CANCEL>START)
CONTROL RESETPress CANCEL > CANCEL > START to enter Service Mode
Diagnostics Mode (Auto Test)Press CANCEL > CANCEL > START
DISPLAYPress CANCEL > CANCEL > START to enter Service Mode
ENG MODEPress CANCEL > CANCEL > START to enter Service Mode
ENG MODE (Engineering Mode)Enter diagnostic mode (CANCEL>CANCEL>START), scroll to 'ENG MODE' (step 2)
FAULTSPress CANCEL > CANCEL > START to enter Service Mode
MRC Control Module Diagnostic ModePress CANCEL > CANCEL > START
Temperature AdjustmentPress OVEN LIGHT for 5 seconds
TEST MODEPress CANCEL > CANCEL > START to enter Service Mode
TEST ON (Relay Checks)Press CANCEL > CANCEL > START
TEST ON (Relay Control)Enter diagnostic mode (CANCEL>CANCEL>START)
USAGEPress CANCEL > CANCEL > START to enter Service Mode
VERSIONPress CANCEL > CANCEL > START to enter Service Mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Ikea range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass