Model reference

Jenn-Air JMC6224HL0

Microwave

6 documents34 error codes4 service modes

Available documentation

Tech Sheet

tech sheet w11508938 reva48 pg
Covers this model
Wiring Sheet - W11325860 - Rev B2 pg
Covers this model
tech sheet w11686738 revA2 pg
Covers this model

Installation Guide

Test Test Test16 pg
Covers this model
Installation Instructions16 pg
Covers this model
Trim Kit12 pg
Covers this model

MyPros+ Max

Diagnose your Jenn-Air JMC6224HL0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Jenn-Air Microwave

CONFIGURATION_PARAMETERS_MYSMATCH_WITH_HW on my Jenn-Air JMC6224HL0

M+

Configuration parameters mismatch with

From Tech Sheet W13793841, p.13:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (34)

CodeMeaning

CONFIGURATION_PARAMETERS_MYSMATCH_WITH_HWConfiguration parameters mismatch with hardware.Err4Ambient temperature sensor value out of allowed range (shown during test mode…Err7Humidity sensor value out of allowed range (shown during test mode when…F1E1System Failure F1E3ADC_DIAG F2E1ADC_DIAG F2E2Keypad/Display Disconnected.F2E4HMI Over Temperature.F2E5HMI Fault.F3E0Temperature sensor Failure F3E3Oven meat probe open or shorted.F4E1Temperature Error F4E2Magnetron Temp Sensor Error.F4E4Humidity Sensor Error F4E7MWO Meat Probe/Temperature Probe connector or probe Failure.F5E0Latch error F5E1Latch Error F5E2Door Switch MWO.F6E0WO Cavity Temperature Sensor Error (sub-code 02).F6E1Probe temperature greater than 30°C + Temperature set by the user.F6E4Stuck/Shorted Key F6E6ADA Communication error (lost communication).F7E2Boiler NTC Out of Range outside the range -20°C to +145°C.F8E8This error appears if the drain pump is ON for maximum time and the water level…F9E0Miswire Detection Error.FACTORY_TEST_NOT_PERFORMEDFactory test not performed.FCE1WiFi Module Connection.FCE2No link between WiFi module and wireless router.FCE3No link between WiFi module and internet.FCE4Antenna A not operational.

View all 34 error codes

FCE5Antenna B not operational.PEC_1_COOKINGSystem Failure PEC_1_IDLESystem Failure PEC_3_FAILSystem Failure

Service modes (4)

Diagnostics Mode (touchscreen UI)["Press 'Setting', scroll down and press 'Info.'","Press 'Service and Support.'","Verify the model…
Self-Diagnostic Test Mode (touch keypad / microwave hood combination)["Press and hold CANCEL/OFF while opening the door.","While still holding the CANCEL/OFF button…
Service Diagnostic Mode / Component Activation["1
U.I. Configuration Mode["Press 'Setting', scroll down and press 'Info.' Press 'Service and Support.'","Check that the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass