Model reference

Jenn-Air 4800

Range

12 documents76 error codes19 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10185202 - Rev B (FR)12 pg
    Covers this model
  • TECH SHEET - W10185201 - Rev B12 pg
    Covers this model
  • Tech Sheet - W10185204 - Rev B (FR)12 pg
    Covers this model
  • TECH SHEET - W10185203 - Rev B12 pg
    Covers this model
  • TECH SHEET12 pg
    Covers this model
  • Tech Sheet - 8303952 - Rev A (EN)12 pg
    Covers this model
  • TECH SHEET - 8303951 - Rev A12 pg
    Covers this model
  • FICHE TECHNIQUE - 8304416 - Rev A (FR)12 pg
    Covers this model
  • Tech Sheet - W10220953 - Rev A (FR)12 pg
    Covers this model
  • TECH SHEET - Whirlpool Oven KEBS107SSS0012 pg
    Covers this model
  • TECH SHEET - KA Oven KEBK101SSS0012 pg
    Covers this model
  • Fiche technique - Tech Sheet W1022095516 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air 4800.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (76)

View all 76 error codes
E3 F3Meat probe shorted.E3 F6Mini oven/warm drawer over temperature (oven not equipped with this feature).E3F3Meat probe shorted.E3F6Mini oven/warm drawer over temperatureE4Ice maker self-diagnosticsE4 F6User interface / appliance manager mismatch.E4F6User interface / appliance manager mismatch.E5 F6No cavity size command programmed in control.E5F6No cavity size command programmed.F0 E0No failure (GOOD)F0E0No failure detected (GOOD)F1 E0Internal failureF1 E1Internal failureF1E0Internal control board failureF1E1Internal failureF2 E0Keypad disconnected.F2 E1Stuck or shorted key on keypad.F2E0Keypad disconnected.F2E1Stuck or shorted key.F3 E0Main oven sensor shorted or open.F3 E1Lower main oven sensor shorted or open.F3 E2Warming drawer sensor shorted.F3 E3Meat probe shorted.F3E0Warming drawer sensor shorted or open.F3E1Lower main oven sensor shorted or open (oven not equipped with this feature).F3E2Oven temperature sensor shorted or open (upper oven, lower oven, or meat probe…F3E3Meat probe shorted.F5 E0Door and latch switch do not agree.F5 E1Door latch not operating.F5E0Door and latch switch do not agreeF5E1Door latch not operatingF6 E0Lost communications between user interface and appliance manager.F6 E1Cook oven over temperature.F6 E2Clean oven over temperature.F6 E3Mini oven/warm drawer over temperature.F6 E4User interface/appliance manager mismatch.F6 E5No cavity size commandF6E0Lost communications between user interface and appliance manager.F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperature (oven not equipped with this feature).F6E4User interface/appliance manager mismatch.F6E5No cavity size command.OPThermistor is open, displayed during service test thermistor readings.PAIce maker self-diagnosticsSHThermistor is shorted, displayed during service test thermistor readings.

Service modes (19)

  • Cavity size programming["Unplug oven or disconnect power","Wait 10 seconds, plug in oven or reconnect power","Enter…
  • cavity_size_programming1. Disconnect power, wait 10 seconds, reconnect. 2. Enter diagnostic mode
  • Clear Last Error Code1
  • clear_last_error_code1
  • component_activation_tests["Enter diagnostic mode (OFF, OFF, START) within 120 seconds of powering on.","Press BAKE to…
  • diagnosticPress OFF, OFF, START
  • Diagnostic mode["Press OFF","Press OFF","Press START"]
  • Diagnostic Mode - Troubleshooting KeystrokesWhile in Diagnostic Mode (OFF, OFF, START), use the following keys
  • diagnostic_component_activationEnter diagnostic mode (OFF, OFF, START), then use individual keys to activate components.
  • diagnostic_troubleshooting_keystrokesWhile in Diagnostic mode (entered via OFF, OFF, START)
  • Fahrenheit to Celsius conversion["Press OPTIONS","Press 1 to toggle temperature between Fahrenheit and Celsius settings"]
  • Fahrenheit/Celsius conversion["Press OPTIONS, then press 1 to toggle between Fahrenheit and Celsius."]
  • Fahrenheit/Celsius toggle["Press OPTIONS","Press 1"]
  • fault_code_clearing1. Disconnect power, wait 10 seconds, reconnect. 2. Enter diagnostic mode
  • Sabbath Mode exit["Press OPTIONS","Press 7"]
  • Service Diagnostics Mode["On the Main (Eyebrow) UI, press and hold both temperature '-' buttons simultaneously for 3…
  • Temperature calibration adjustment["Press OPTIONS","Press 6 to set the calibration","On double ovens only, press UPPER OVEN or LOWER…
  • Temperature Calibration mode["Press OPTIONS","Press 6","On double ovens only, press UPPER OVEN or LOWER OVEN to select…
  • temperature_calibration1

Full entry steps, exit procedures, and test sequences are available in Max.

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax