mypros+
Model reference

Jenn-Air JDRP636HM01

Range

11 documents50 error codes16 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11565461 - Rev A2 pg
    Covers this model
  • Tech Sheet - W11508930 - Rev A2 pg
    Covers this model
  • Tech Sheet100 pg
    Covers this model
  • JDRP536HL tech sheet w11202265 reva100 pg
    Covers this model

Service Manual

  • Tech Manual39 pg
    Covers this model

Service Flash

  • Technical Service Pointer3 pg
    Covers this model

Tech Tip

  • Third Rack1 pg
    Covers this model

Installation Guide

  • Installation Instructions48 pg
    Covers this model
  • Installation Instructions72 pg
    Covers this model
  • Installation Instructions72 pg
    Covers this model

Other

  • tech manual w11202265 revb100 pg
    Covers this model
MyPros+ Max

Diagnose your Jenn-Air JDRP636HM01.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (50)

CodeMeaning
F1 E0Oven user interface failure.F1 E1Internal Oven Appliance Manager (AM) error.F1E0User Interface Board EEPROM Communication ErrorF1E1Control Relay Board EEPROM Communication ErrorF2 E0Keypad disconnected.F2 E1Stuck or shorted key on keypad.F2E0Keypad disconnected.F2E1Stuck KeyF2E2Oven Knob Rotary Encoder Open/ShortedF3 E0Main oven temperature sensor open or shorted.F3 E1Bottom oven temperature sensor open or shorted.F3 E3Meat probe connector jack or meat probe shorted.F3E0Main Oven Sensor Open or ShortedF3E1Left Oven Sensor Open or ShortedF3E3Main Oven Meat Probe Short-CircuitF3E9Left Oven Meat Probe Short-CircuitF5 E0Door and latch switch do not agree (main/upper oven).F5 E1Latch not operating (main/upper oven).F5 E3Door and latch switch do not agree (lower oven).F5 E4Latch not operating (lower oven).F5E0Main Oven Door Latch SwitchF5E1Main Oven Door Latch MotorF5E3Left Oven Door Latch SwitchF5E4Left Oven Door Latch MotorF6 E0Oven user interface lost communication.F6 E1Over temperature (main/upper oven).F6 E3Over temperature (lower oven).F6 E4User Interface / Appliance Manager state status mismatch.F6 E6Oven appliance manager lost communication (main/upper oven).F6 E9Oven appliance manager lost communication (lower oven).
View all 50 error codes
F6 EAUser Interface over temperature.F6E0User Interface ConnectionF6E1Main Oven Over Temperature LimitF6E3Left Oven Over Temperature LimitF6E4Control StatusF6E6Main Oven Control ConnectionF6E9Left Oven Control ConnectionF6EAUser Interface over temperature.F7E1Boiler Over Temperature Limit (steam models)F7E2Boiler Temperature Out of Range (steam models)F8 E0Low fan speed underspeed.F8 E1Low fan speed overspeed.F8 E2High fan speed underspeed.F8 E3High fan speed overspeed.F8E0Main Oven Cooling Fan speed low or not functioningF8E1Left Oven Cooling Fan Speed LowF8E2Main Oven Cooling Fan Speed HighF8E3Left Oven Cooling Fan Speed HighF9 E0Product not wired correctly (neutral connection may be switched with L1 or L2).F9E0Power Input

Service modes (16)

  • Cavity Size Select1
  • cavity_size_select1
  • diagnosticPress CANCEL > CANCEL > START on the control panel.
  • Diagnostics modePress CANCEL > CANCEL > START
  • Diagnostics Mode Entry["Ensure appliance is in standby mode.","Set Mode Selector knob to Bake position and Temperature…
  • Error Codes (Fault History)1
  • error_codes_view1
  • Fault Code DisplayWhile in Diagnostics Mode, rotate the Mode Selector knob clockwise until the top LEDs are on (Fault…
  • Manual DiagnosticAfter entering Service Diagnostic Mode, rotate the Mode Selector knob clockwise until the top and…
  • Manual DiagnosticsWhile in Diagnostics Mode, rotate the Mode Selector knob clockwise until top and right LEDs are on…
  • Relay Activation1
  • relay_activation1
  • Service Diagnostic Mode1
  • Software VersionFor Engineering only
  • Status Screen1
  • status_screen1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass