Model reference
Magic Chef 83EA-1K
Cooktop
12 documents66 error codes17 service modes
Available documentation
Tech Sheet
- Instruction Sheet - 9755067 - Rev I6 pg
- TECH SHEET - W10204803 - Rev A7 pg
- Wiring Diagram - W10873901 -Rev A.pdf2 pg
- TECH SHEET7 pg
- Tech Sheet - 83038527 pg
Service Manual
- Technical Education Job Aid 4317409 KAC-47 Touch-activated Electronic Induction Cooktop40 pg
- Touch-Activated Electronic Induction Cooktop40 pg
- Service Manual - Touch-Activated Electronic Induction Cooktop40 pg
Tech Tip
- Instruction Sheet - 818463712 pg
- Instruction Sheet - 816975420 pg
- Instruction Sheet - 818443020 pg
- Instruction Sheet - 816969620 pg
MyPros+ Max
Diagnose your Magic Chef 83EA-1K.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (66)
CodeMeaning
c1Insufficient line voltage (less than 185 VAC).c2Inductor temperature failure; cooktop has overheated.c3Radiator temperature failure; cooktop has overheated.ClThe line power supply voltage is too low.EA sensor has been pressed for too long (>5 seconds), possibly due to spilled…e0Electronic board failure (shorted or damaged component).e1Electronic board failure (problem in damaged component).e2Fan will not operate.e3NTC sensor open circuit.e4NTC sensor shorted.Er32A touch control of a 2-element cooktop is connected to a 4-element cooktop, or…ErXYThe touch control has an internal failure (except Er32).F0No communications between the touch control and electronic boards.F0-E0Default F codeF1 E0EEPROM communication error.F1 E1EEPROM checksum error.F1 E2UL A/D errors.F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0Electronic control malfunction (E0 variant).F1-E0/E1/E2Electronic control malfunction.F1-E1Electronic control malfunction (E1 variant).F1-E2Electronic control malfunction (E2 variant).F1-E3Electronic control malfunction (E3 variant).F1-E3/E4/E5Electronic control malfunction.F1-E4Electronic control malfunction (E4 variant).F1-E5Electronic control malfunction (E5 variant).F2NTC temperature of the touch control is excessively high (>100°C); cooking…F2 E0Shorted key error.F2 E1Keytail unplugged.View all 66 error codes
F2-E0Keypad keytail not connected.F2-E1Keypad keytail not connected.F2-E3Key held down too long, or key is shorted.F3 E0Top oven sensor open.F3 E1Top oven sensor shorted.F3 E2BAKE range over temperature.F3 E3CLEAN range over temperature.F3 E4Bottom oven sensor open.F3 E5Bottom oven sensor shorted.F3-E0Temperature sensor (lower) opened.F3-E1Temperature sensor (lower) shorted.F3-E2Temperature sensor (microwave) opened.F3-E3Temperature sensor (microwave) shorted.F4NTC temperature of the touch control is excessively high (>100°C); none of the…F4-E0Meat probe shorted.F5 E0Door switches do not agree.F5 E1Door latch not operating.F5-E0Lower cavity over temperature while cleaning.F6-E0Lower cavity over temperature during cooking.F6-E1Microwave cavity over temperature during cooking.F8Maximum cooking time has been exceeded for the corresponding cooking zone…F8 E0Refrigeration incorrect operation.F8-E0Self-clean latch will not lock.F8-E0/E1/E2/E3/E4Function not used.F8-E1Self-clean latch will not unlock.F8-E2Oven over temperature while door open and latch lock.F8-E3Oven over temperature while door open and latch unlock.F8-E4Oven over temperature while door close and latch unlock.FOPNo communications between the right and left electronic boards.Memory FailureControl board memory/software fault detected during Field Service Test; Heated…Motor high currentWash motor drawing excessive current detected during Field Service Test; Normal…Motor low currentWash motor drawing insufficient current detected during Field Service Test…SABOven is in Sabbath Mode.Thermistor failureThermistor fault detected during Field Service Test; Heavy Wash LED flashes…Turbidity Sensor failureTurbidity sensor fault detected during Field Service Test; Rinse Only LED…U400Electronics have been connected erroneously at 400V; warning appears when…
Service modes (17)
- Bake temperature offset adjustment1
- Default F code display (no fault check)Press and hold '0' key for 5 seconds
- Default F code display (no-fault check)Press and hold '0' key for 5 seconds
- Default F code display (no-fault verification)Press and hold '0' key for 5 seconds
- Default fault code display (F0-E0)Press and hold '0' key for 5 seconds (only displays if no pre-existing faults).
- diagnostics1
- Fahrenheit to Celsius conversionPress the BROIL pad for 5 seconds
- Fault code displayPress and hold UPPER OFF key for 5 seconds
- Field Service TestPress the Heavy Wash key 5 times followed by the Start key within 6 seconds.
- Hidden fault code displayPress and hold UPPER OFF key for 5 seconds
- Manual Function TestPress the Normal Wash key 5 times followed by the Start key within 6 seconds
- Sabbath Mode checkIf 'SAB' appears in digital display, oven is in Sabbath Mode.
- Sabbath Mode exitIf 'SAB' appears in digital display, press and hold the '6' key for 5 seconds to end Sabbath Mode.
- Sales Floor Demo ModePress Extra Rinse keypad 5 times within 6 seconds.
- Temperature unit conversion (Fahrenheit to Celsius)Press the BROIL pad for 5 seconds
- Water Filter Input (WFI) Test - Dispenser Valve1. Open the refrigerator door. 2. Depress the refrigerator light switch. 3. Place a container under…
- Water Filter Input (WFI) Test - Ice Maker Valve1. Open the refrigerator door. 2. Depress the refrigerator light switch. 3. Activate the ice maker…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Magic Chef cooktop models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax