mypros+
Model reference

Magic Chef CES3759BCW

Range

6 documents36 error codes48 service modes

Available documentation

Tech Sheet

  • Electric Slide-In Range—Technical Information8 pg
    Covers this model

Service Manual

  • Service Manual - 1602629945 pg
    Covers this model
  • Maytag Heritage Wiring Diagrams _ Fault Codes MC 1124 pg
    Covers this model
  • Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model
  • FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
    Covers this model

Bulletin

  • Technical Bulletin - Hot Surface Indicator Light Change1 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef CES3759BCW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (36)

CodeMeaning
1c1cShorted key detected on control circuit board.1c2cKeyboard tail disconnected from control circuit board.1c31Cancel key circuit problem1c32Cancel key circuit problem (H1 control variant).1c4cPower micro communication failure (CRC invalid).1c6cEEPROM error1c7cControl not calibrated1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error1d11Runaway oven temperature (650°F) with door unlocked1d12Runaway oven temperature (650°F) with door unlocked (H1 second cavity variant).1d21Runaway oven temperature (950°F) with door locked1d22Runaway oven temperature (950°F) with door locked (H1 second cavity variant).3d11Oven temperature sensor open3d12Oven temperature sensor open (H1 second cavity variant).3d21Oven temperature sensor shorted3d22Oven temperature sensor shorted (H1 second cavity variant).3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch position failure4d12Door switch position failure (H1 second cavity variant).4d21No reverse airflow fan rotation detected (no or low RPM) during cook or clean…4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse airflow fan is on when it should be off (H1 control only).4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure4d52Door switch circuit failure (H1 second cavity variant).
View all 36 error codes
9d11Door latch will not lock9d12Door latch will not lock (H1 second cavity variant).9d21Door latch will not unlock9d22Door latch will not unlock (H1 second cavity variant).9d31Door latch state unknown9d32Door latch state unknown, both locked and unlocked (H1 second cavity variant).

Service modes (48)

  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H1)Press and hold the Autoset pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H2.5)Press and hold Upper Cancel and Autoset pads for 3 seconds
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (H3)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up
  • Diagnostic Code Display Mode (M1/M2)Diagnostic Code Display Mode can only be started within 30 seconds when powering up the control.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Diagnostic Code Display Mode (NSC)Press and hold More + pad for 3 to 5 seconds within 60 seconds of powering up the unit. Cycle…
  • Faults Access (EOC III Controls)1
  • Faults Access (EOC III)1
  • H1 Child LockoutPress and hold Cancel and Cook & Hold pads for 3 to 5 seconds
  • H1 Diagnostic Code Display1
  • H1 Factory Default ResetPress and hold Cancel and Keep Warm pads for 3 to 5 seconds.
  • H1 Oven Temperature Adjustment1
  • H1 Quick Test Mode1. Press and hold CANCEL and BROIL pads for 3 to 5 seconds. 2. Release both pads when control…
  • H1 Sabbath ModeHold CLOCK pad for 3 to 5 seconds to activate.
  • M1 Child LockoutPress and hold Cancel and Cook & Hold pads for 3 to 5 seconds until beep sounds.
  • M1 Diagnostic Code Display1
  • M1 Factory Default ResetPress and hold Cancel and Keep Warm pads for 3 to 5 seconds until beep sounds.
  • M1 Oven Temperature Adjustment1
  • M1 Quick Test Mode1. Must enter within 5 minutes of power up. 2. Press and hold Cancel and Broil pads for 3 to 5…
  • M1 Sabbath Mode1
  • M2 Child LockoutPress and hold Cancel and Cook & Hold pads for 3 to 5 seconds
  • M2 Diagnostic Code Display1
  • M2 Factory Default ResetPress and hold Cancel and Keep Warm pads for 3 to 5 seconds.
  • M2 Oven Temperature Adjustment1
  • M2 Quick Test Mode1. Must enter within 5 minutes of power up. 2. Press and hold CANCEL and BROIL pads for 3 to 5…
  • M2 Sabbath ModeHold CLOCK button for 3 to 5 seconds to activate.
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • One-Watt Standby Mode (NSC)Press and hold Cancel and Less
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (EOC III)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H1 Convection Model)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H1 Non-Convection Model)1. Press and hold Cancel and Toast pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H2/H2.5 Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Control)1. Press and hold Upper Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Control)1. Press and hold Cancel and Broil pads for 3 seconds. 2. Release both pads. 3. Press pads
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Quick Test Mode (NSC Non-Self Cleaning Control)1. Press and hold Cancel and Broil pads for 3 to 5 seconds within 5 minutes of power-up. 2. Release…
  • Service Mode (EOC III Controls)1
  • Service Mode (EOC III)1
  • Test Mode (UH Control)1
  • Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass