Magic Chef D3550-3WC-2X

Error codes (26)

Service modes (49)

• Help Mode (dAS mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
• Help Mode (PD models)["Open the service door.","Press the LOWER MIDDLE keypad until the display reads 2.XX.","Press the…
• P-01 Cancel Cycle, Reset Errors, and Clear EscrowFrom diagnostic test modes, navigate to P-01 display and press START
• P-01: Cancel Program, Error Reset, Clear Stored Credit["Enter Service Diagnostic Test Modes (steps 1-3).","Press START when 'P-01' is displayed."]
• P-02 Cycle CreditFrom diagnostic test modes, navigate to P-02 display and press START
• P-02: Program Credit["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-02 using LOWER CENTER…
• P-03 Quick Overview TestFrom diagnostic test modes, navigate to P-03 display and press START
• P-03: Quick Overview Test Program["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-03 using LOWER CENTER…
• P-04 Manual Overview TestFrom diagnostic test modes, navigate to P-04 display and press START
• P-04: Manual Overview Test Program["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-04 using LOWER CENTER…
• P-05 Button TestFrom diagnostic test modes, navigate to P-05 display and press START. TEST will be displayed. Press…
• P-05: Button Test["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-05 using LOWER CENTER…
• P-06 Drain and SpinFrom diagnostic test modes, navigate to P-06 display and press START
• P-06: Drain and Spin["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-06 using LOWER CENTER…
• P-07 UI DiagnosticsFrom diagnostic test modes, navigate to P-07 display and press START
• P-07: UI Diagnostics["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-07 using LOWER CENTER…
• P-08 Clean Washer CycleFrom diagnostic test modes, navigate to P-08 display and press START
• P-08: Washer Clean Cycle["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-08 using LOWER CENTER…
• P-09 Factory DiagnosticsFrom diagnostic test modes, navigate to P-09 display and press START.
• P-09: Factory Diagnostics["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-09 using LOWER CENTER…
• Service Access CodeOnly functions on washers set up for 0 vend price without Special Pricing and Coin/Debit Option set…
• Service Access Code (free-vend models only)1. Open the door. 2. Within 10 seconds, press in sequence
• Service Access Code (key dance entry without console removal)["Washer must be set for 0 vend price, no Special Pricing, and Coin/Debit Option set to…
• Service Access Code (key dance)["Only available on washers set to free vend (6 00) with no Special Pricing set-up and Coin/Debit…
• Service Access Code (keypad entry)["Open the door.","Press the upper left keypad.","Press the lower right keypad.","Press the upper…
• Service Access Code (no console removal)["Open the door.","Press the upper left key pad.","Press the lower right key pad.","Press the upper…
• Service Access Code (Technician Entry)["This method is only available on washers set for free operation (code 6 00).","Open the…
• Service Access Code (Technician key dance)Only available on washers set to free vend (6 00) with no Special Pricing and Coin/Debit Option set…
• Service Access Code (Technician)Only works on washers set to free vend (6 00) with no Special Pricing and Coin/Debit Option set to…
• Service Diagnostic Test Modes1) Turn off power, remove service door on metercase models or remove AA1 Service/Coin Jumper from…
• Service Diagnostic Test Modes (P-01 through P-09)["Make sure power is turned off.","Remove the service door on metercase models, or remove the AA1…
• Service/Set-up Mode (PD models)["Insert service access door key, turn, and lift to remove service access door."]
• Service/Set-up Mode (PR Models via AA1 jumper)1
• Service/Set-up Mode (PR Models with set-up card)["Insert a set-up card (supplied by the reader manufacturer) into the card slot."]
• Service/Set-up Mode (PR models)["Install debit card reader per manufacturer instructions.","Insert a set-up card (supplied by…
• Service/Set-up Mode (via service connector removal)["Unplug washer or disconnect power.","Open console, disconnect plug on service connector, close…
• Service/Setup Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door.","The washer enters…
• Service/Setup Mode (PR Models via AA1 connector)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
• Service/Setup Mode (PR Models via AA1 jumper)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1 connector on circuit…
• Service/Setup Mode (PR Models)Insert a set-up card (supplied by reader manufacturer) into the card slot. If no set-up card is…
• Set-Up Mode (PD Models)Insert service access door key, turn, and lift to remove service access door
• Set-Up Mode (PR Models)Install debit card reader per manufacturer instructions, then insert a set-up card (supplied by…
• Setup Mode (PD Models)Insert service access door key, turn, and lift to remove service access door
• Setup Mode (PR Models via AA1 jumper removal)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1 connector on circuit…
• Setup Mode (PR Models)Insert a set-up card (from reader manufacturer) into the card slot. If no set-up card is available…
• Setup/Configuration Mode (PD models)["Insert the service door access key, turn and lift to remove the service access door."]
• Setup/Configuration Mode (PR models)["Insert the setup card (provided by card reader manufacturer) into the card reader.","If no setup…
• Technician Service Access CodeOnly available on washers set to free vend (6 00) with no Special Pricing set-up, and Coin/Debit…
• Technician Service Access Code (free vend models only)["Washer must be set to free vend (6 00), no Special Pricing, Coin/Debit Option set to…

Full entry steps, exit procedures, and test sequences are available in Max.