mypros+
Model reference

Magic Chef RA14GN-1P

Refrigerator

7 documents61 error codes25 service modes

Available documentation

Tech Sheet

  • Wiring Diagram - W10703187 - Rev B2 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 818520212 pg
    Covers this model

Installation Guide

  • Installation Instructions28 pg
    Covers this model
  • Installation Instructions44 pg
    Covers this model
  • Installation Instructions8 pg
    Covers this model
  • Installation Instructions88 pg
    Covers this model
  • Installation Instructions64 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef RA14GN-1P.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (61)

CodeMeaning
CAAverage current limit tripCECommunications errorCIInstantaneous current limit tripErProcessor reset errorF0E0No error(s) found.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected during rinse cycle (water temperature 40.5°C /…F0E5Off balance load detected during operation.F1E0Internal failureF1E1Main control fault detected.F1E2Motor control fault; fault of the motor control section of the main control.F1E3Internal errorF1E4Internal errorF1E5Internal errorF2E0Keypad disconnected.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and user interface; the UI identification does not…F3E0Main oven sensor open or shorted.F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F3E3Meat probe shorted.F4E1Convection thermistor error (microwave sensors).F4E2Internal temperature sensor error (microwave sensors).F4E4Humidity sensor error (microwave sensors).F4E9AccuPop™ error.F5E0Door and latch switch do not agree.F5E1Lid switch fault; lid is in locked state but lid switch is open, or main…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…
View all 61 error codes
F6E0Lost communication between user interface and appliance manager.F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E3No cavity size command.F6E4User interface / appliance manager mismatch.F6E5Mini oven / warm drawer over temperature.F7E0Water is not high enough or water did not boil fast enough.F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E2Boiler NTC out of range.F7E3Improper filter reset.F7E4Conductivity sensor not connected.F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E0Blower low speed too low.F8E1No fill / long fill; water level does not change for a period of time or water…F8E2Blower high speed too low.F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…FCE2Appliance not linked to the wireless router.FCE3Appliance not linked to the Internet.FCE7Appliance failed to connect to the wireless router.FLOverfill conditionLdLong drainLFLong fillLSLid switch errorobOff balancePFPower failureSLSuds lockSrStuck relay

Service modes (25)

  • Automatic Service DiagnosticsWith control OFF, press PREWASH OPTIONS → WASH TIME → PREWASH OPTIONS → WASH TIME within 5 seconds.
  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • Cavity Size Programming["Unplug range or disconnect power.","Wait 10 seconds, then plug in range or reconnect…
  • Clear Error HistoryAfter fixing errors, enter the Diagnostics menu by pressing the three key sequence within 8…
  • Clear Last Error Code["Unplug range or disconnect power.","Wait 10 seconds, reconnect or plug in range.","Enter…
  • Diagnostic Menu - Extended Mode1. Enter Diagnostic Mode (OFF, OFF, START). 2. Configure cavity size to 30 inches by pressing 30…
  • Diagnostic ModePress OFF, OFF, START.
  • Diagnostics Mode["Press OFF key to place oven in idle state.","Press OFF, OFF, START to enter Diagnostics Mode."]
  • Diagnostics Mode - Screen Navigation["Enter Diagnostics Mode by pressing OFF, OFF, START.","Screen 1
  • Diagnostics Mode - Troubleshooting Keystrokes["Enter Diagnostics Mode by pressing OFF, OFF, START.","Press BAKE key to activate Bake…
  • Diagnostics Mode (Alternate entry for failure code check)Press CANCEL
  • Diagnostics Mode (Option A)Press the 3-key sequence Settings
  • Diagnostics Mode (Option B)1. Press Tools
  • Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • Keypad and LED TestWith control OFF, press SET DELAY TIME → END OF CYCLE SIGNAL → SET DELAY TIME → END OF CYCLE SIGNAL…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • Model ID and Cavity Size Programming (after UI replacement)1
  • Nutate and Recirculate TestWith control OFF, press SET DELAY TIME → END OF CYCLE SIGNAL → SET DELAY TIME → END OF CYCLE SIGNAL…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • Spin and Drain TestWith control OFF, press SET DELAY TIME → END OF CYCLE SIGNAL → SET DELAY TIME → END OF CYCLE SIGNAL…
  • Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • Water Inlet and Dispenser Valve Operating PS TestWith control OFF, press SET DELAY TIME → END OF CYCLE SIGNAL → SET DELAY TIME → END OF CYCLE SIGNAL…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass