mypros+
Model reference

Magic Chef RB19JA-4A

Refrigerator

5 documents36 error codes12 service modes

Available documentation

Tech Sheet

  • TechSheet-W10843072-RevA(FR).pdf8 pg
    Covers this model

Tech Tip

  • Instruction Sheet16 pg
    Covers this model

Installation Guide

  • Installation Instructions30 pg
    Covers this model
  • Installation Instructions40 pg
    Covers this model
  • Installation Instructions32 pg
    Covers this model
MyPros+ Max

Diagnose your Magic Chef RB19JA-4A.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (36)

CodeMeaning
F0 E0No fault found.F1 E2Lost communication with power board.F1 E3Configuration jumper change; freestand, electric switches or P3 pins 1 to 5…F1 E4Oven sensor not calibrated.F1 E5Meat probe not calibrated.F1 E6Display board EPROM access failure.F1 E7Power board EPROM access failure.F1 E8Improper keypad feedback from power board supply lift.F1 E9Unstable keyboard gain.F1 EAExceeded stack warning level.F1E0EEPROM communication error.F1E5Sensor out of range.F1E7Circuit board thermistor open or short-circuited.F2 E0User is cleaning too long or keypad is disconnected.F2 E1Cancel key invalid.F2 E3Key held down too long or keyboard short or spill on switch surface.F2E0Keypad disconnected.F2E1Key stuck.F2E2Cancel key error.F3 E0Oven sensor open circuit.F3 E3Shorted oven sensor.F3 E4Oven temperature too high (runaway condition).F3E0Main oven sensor open or short-circuited.F3E2Warming drawer sensor open or short-circuited.F4 E0Meat probe shorted (less than 1500 ohms).F5 E1Self clean latch not locking.F5 E5Self clean temperature not achieved after 30 minutes.F5 E7Door unlocked but will not unlatch during clean cycle.F5E0Door and switch mismatch (clean mode, on some models).F5E1Door latch not functional (clean mode, on some models).
View all 36 error codes
F6E1Bake mode over-temperature condition.F6E2Clean mode over-temperature condition.F6E3Warming drawer over-temperature condition.F7 E0Invalid latch switch reading.F7 E1Invalid door switch reading.PFPower failure occurred (not a failure mode).

Service modes (12)

  • Auto TestAfter entering diagnostic mode (CANCEL>CANCEL>START), press the up arrow, '+', or '3' key to scroll…
  • Diagnostic / Service ModePress CANCEL > CANCEL > START
  • DISPLAYFrom diagnostic mode, scroll to step 5 (DISPLAY).
  • End of Service Test Sequence (Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • End of Service Test Sequence (Non-Convection Units)["Connect unit to power, set power ON and wait until CONTROL LOCK clears and display shows PF…
  • ENG MODE (Engineering Mode)From diagnostic mode, scroll to step 2 (ENG MODE)
  • FAULTSFrom diagnostic mode, scroll to step 7 (FAULTS).
  • RELAY USAGEFrom diagnostic mode, scroll to step 8 (RELAY USAGE).
  • TEST MODEFrom diagnostic mode, scroll to step 3 (TEST MODE)
  • TEST ON (Relay Control)Displayed immediately upon entering diagnostic mode (CANCEL>CANCEL>START)
  • USAGEFrom diagnostic mode, scroll to step 1 (USAGE) using up arrow, '+', or '3'.
  • VERSIONFrom diagnostic mode, scroll to step 4 (VERSION).

Full entry steps, exit procedures, and test sequences are available in Max.

Related Magic Chef refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass