mypros+
Model reference

Maytag VEND-10.G

Microwave

5 documents54 error codes27 service modes

Available documentation

Installation Guide

  • Installation Instructions48 pg
    Covers this model
  • Installation Instructions36 pg
    Covers this model
  • Installation Instructions16 pg
    Covers this model
  • Installation Instructions12 pg
    Covers this model
  • Instrucciones de instalacion52 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag VEND-10.G.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (54)

CodeMeaning
d 13Coin 2 errord 16Generation 2 debit card reader errord 5Coin 1 errord 9Low voltage detection errord1Dryer door sense error on control board or due to power line interference…d12Motor sense error on control board or due to power line interference; cycles…d13Coin 2 errord16Generation 2 debit card reader errord36Stuck key errord4Dryer motor control circuit error; cycles and customer display disabled until…d5Coin 1 errord9Low voltage detection errorF 01CCU errorF 03Accelerometer failureF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnectedF 34Load detected in washer during washer cleanout cycle.F 37Water level out of range lowF 38Water level out of range high
View all 54 error codes
F 70Communication failure between CCU and UI (User Interface).F 73UI failureF 74UI failureF01CCU (Central Control Unit) errorF03Accelerometer failureF04CCU dislodged from mounting or accelerometer failure on CCU.F11MCU (Motor Control Unit) has a failure, possibly due to a repeating under or…F20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.F29Door unlock errorF31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F37Water level out of range lowF38Water level out of range highF70Communication failure between CCU and UI (User Interface).F73UI failureF74Communication error within the User Interface (same as F73).

Service modes (27)

  • Code Display Mode["PD Models
  • Cycle Credit["Enter Washer Diagnostic Mode (entire display flashing).","Press the PERM
  • Diagnostic Mode["Enter the set-up mode first (see set-up mode entry).","While in any of the set-up codes 1 through…
  • Flashing Mode["PD Models
  • Help Mode["Enter the set-up mode first.","Navigate to special pricing option step 2.XX (or while dAS…
  • Help Mode (dAS mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
  • Help Mode (PD models)["Open the service door.","Press the LOWER MIDDLE keypad until the display reads 2.XX.","Press the…
  • Manual Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WHITES button to start the…
  • Quick Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WOOLENS button to start the…
  • Quick Spin Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the COLORS button to start the…
  • Service Access Code (key dance)["Only available on washers set to free vend (6 00) with no Special Pricing set-up and Coin/Debit…
  • Service Access Code (keypad entry)["Open the door.","Press the upper left keypad.","Press the lower right keypad.","Press the upper…
  • Service Access Code (No Console Removal)["Only functions on washers set up for 0 vend price without any Special Pricing set-up, and…
  • Service Access Code (Technician)Only available on washers set to free vend (6 00)
  • Service Diagnostic Test Modes1
  • Service/Set-up Mode (PD models)["Insert service access door key, turn, and lift to remove service access door."]
  • Service/Set-up Mode (PR Models with set-up card)["Insert a set-up card (supplied by the reader manufacturer) into the card slot."]
  • Service/Set-up Mode (PR models)["Install debit card reader per manufacturer instructions.","Insert a set-up card (supplied by…
  • Service/Set-up Mode (via service connector removal)["Unplug washer or disconnect power.","Open console, disconnect plug on service connector, close…
  • Set-up Mode["Insert access door key, turn, and lift to remove access door.","Unplug dryer or disconnect…
  • Set-Up Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door."]
  • Set-Up Mode (PR Models)["Install debit card reader per manufacturer's instructions.","Insert a set-up card (supplied by…
  • Setup Mode (PD Models)1
  • Setup Mode (PR Models)Insert a set-up card (supplied by the reader manufacturer) into the card slot
  • Setup Mode (via Service Connector)1
  • Washer Cleanout Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the BRIGHTS button to start the…
  • Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (set-up mode).","Press and hold the DELICATES AND KNITS…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass