mypros+
Model reference

Maytag WOES3027LS00

Oven

5 documents40 error codes9 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11600302 - Rev B2 pg
    Covers this model

Service Manual

  • KitchenAid Job Aid W10807512 - 27 & 30" Built-In Single and Double Wall Ovens52 pg
    Covers this model

Service Flash

  • Installation Pointer - W11672734 - Rev A - Built In Single & Double Wall Oven Flush Installation9 pg
    Covers this model
  • Service Pointer - W11815938 - Rev A - Wall Oven F8E0 Error Code6 pg
    Covers this model

Quick Reference

  • Quick Start Guide3 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag WOES3027LS00.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (40)

CodeMeaning
F1 E0User Interface failureF1 E1Appliance Manager failure.F1E1Upper RTD (Resistance Temperature Detector) is uncalibrated.F1E2Lower RTD (Resistance Temperature Detector) is uncalibrated.F1E5Sensor usage out of range.F1E7PCB thermistor is open or shorted.F1E9WIDE queue full.F2 E0Keypad disconnected from User Interface.F2 E1Stuck or shorted key on keypad.F2E0Keypad is disconnected.F2E1Stuck keypad (a key is stuck or continuously pressed).F2E2Cancel or Off keypad error.F3 E0Main/upper oven temperature sensor open or shorted.F3 E1Bottom/lower oven temperature sensor open or shorted.F3 E3Meat Probe connector jack or Meat Probe shorted.F3E0Main oven sensor (upper) is open or shorted.F3E1Main oven sensor (lower) is open or shorted.F4E1Microwave oven magnetron thermistor is open or shorted.F4E4Microwave oven humidity sensor is open or shorted.F5 E0Door and latch input switches do not agree (main/upper oven).F5 E1Latch not operating (main/upper oven).F5 E3Door and latch input switches do not agree (lower oven).F5 E4Latch not operating (lower oven).F5E0Door and latch switches do not agree (mismatch between door and latch switch…F5E1Latch is not operating.F6 E0Oven User Interface lost communication.F6 E1Over temperature condition (main/upper oven).F6 E3Over temperature condition (lower oven).F6 E4Appliance Manager failure.F6 E6Oven Appliance Manager lost communication (main/upper oven).
View all 40 error codes
F6 E9Oven Appliance Manager lost communication (lower oven).F6 EAUser Interface over temperature condition.F6E0Lost communication with microwave.F6E1Over temperature during cook mode.F6E2Over temperature during clean mode.F8E0Low fan speed underspeed (cooling fan running below minimum low-speed…F8E1Low fan speed overspeed (cooling fan running above maximum low-speed threshold).F8E2High fan speed underspeed (cooling fan running below minimum high-speed…F8E3High fan speed overspeed (cooling fan running above maximum high-speed…F9E0Miswired (incorrect wiring detected).

Service modes (9)

  • Cavity Size SelectEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • cavity_size_selectPress CANCEL > CANCEL > START to enter Diagnostic Mode
  • diagnosticPress CANCEL, then CANCEL, then START.
  • Diagnostic ModePress CANCEL, then CANCEL, then START.
  • Error Code Review and ClearEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • error_code_review_and_clearEnter Diagnostic Mode (CANCEL > CANCEL > START), then press keypad 3 or 6 to scroll to the error…
  • Relay ActivationEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • relay_activationEnter Diagnostic Mode (CANCEL > CANCEL > START), then press keypad 3 or 6 to scroll to the RELAY…
  • Service Diagnostic ModePress CANCEL > CANCEL > START (or OFF > OFF > ON) within 5 seconds.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass