Model reference

Maytag FAV9800AWQ

Name: Maytag FAV9800AWQ
Brand: Maytag

Washer, Dryer

2 documents37 error codes25 service modes

Available documentation

Service Manual

FAV9800AWW Service Manual 1602280898 pg
Covers this model

Tech Sheet

Tech Sheet - 16023174_1602317414 pg
Covers this model

MyPros+ Max

Diagnose your Maytag FAV9800AWQ.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Washer, Dryer

1 on my Maytag FAV9800AWQ

M+

No Drain – The water level fails to

From Tech Sheet W14211148, p.40:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drain pump winding resistance at connector J7. Expected: 12 to 16 ohms at room temperature.

3.Verify the board switches the pump at 120 VAC during the drain cycle.

Part W10876537

Drain pump assembly

Error codes (37)

CodeMeaning

1No Drain 10Unbalance or cabinet hit detected during final spin prevented the spinner from…11Will not remember machine settings 15Stuck Key 16High speed not achieved due to torque 17The lid was not opened after completed wash cycles 18Detected lid lock switch open during cycle when not expected; open lid lock…2Lid failed to unlock after multiple attempts.22Detected lid sensor switch open and the lid locked switch locked during cycle…23Lid is locked at start of cycle 24Motor high RPM detected two times 25Tach signal exists without torque input (abnormal condition only)28Water valve thermistor failure 3No Fill 34Welded system relay 4Lid failed to lock after 11 attempts.40Load bound up 5Continuous unbalanced loads detected during spin only; out of balance circuit.6Locked rotor forcing a shut down; rotor is still locked after 10 attempts.8Water level sensor fault CLLid is closed.dcDistribute Clothes FLFailed to Lock LEWater level sensor fault LLLarge Load Detected.LOLocked: Lid has failed to unlock LrLocked Rotor ndNo Drain nFNo fill odOpen the Lid

View all 37 error codes

oLMachine Paused OPLid is Open PFPower failure SdSuds UBSee Diagnostic Code 10 UCContinuous Unbalanced Circuit ULLatch Unlocked

Service modes (25)

Board Input Test (FAV6800A)While in Service Mode, press the Super Wash key.
Board Output Test (FAV6800A)While in Service Mode, press the Delicates key.
Display Diagnostic CodesEnter Service Mode
Display Diagnostic Codes (FAV6800A)While in Service Mode, press the Wrinkle Control key
Display Diagnostic Codes (FAV9800A)Enter Service Mode to display diagnostic codes
Membrane Pad Test (FAV6800A)While in Service Mode, press the Presoak key, then press individual buttons to test.
Motor Control Board Output Test (FAV6800A)1) Disconnect power
Quick Service Cycle (FAV6800A)While in Service Mode, press the Wash/Rinse Temp up key.
Quick Spin TestEnter Service Mode, then select the Quick Spin Test option on the display.
Quick Spin Test (FAV6800A)While in Service Mode, press the Hand Wash key.
Quick Spin Test (FAV9800A)While in Service Mode, select the Quick Spin Test option.
Service CycleEnter Service Mode, then select Service Cycle option.
Service Cycle (FAV9800A)While in Service Mode, select the Service Cycle option.
Service ModePress the Help and Back keys simultaneously for three seconds or until the control beeps.
Service Mode (FAV6800A)Press and hold the Enviro Plus and Spin Only keys for three seconds or until the control beeps.
Service Mode (FAV6800AW)Press and hold the Enviro Plus and Spin Only keys simultaneously for three seconds or until the…
Service Mode (FAV9800A)Press and hold the Help and Back keys for three seconds or until the control beeps.
Service Mode (FAV9800AW)Press and hold the Help and Back keys simultaneously for three seconds or until the control beeps.
System CheckEnter Service Mode, then select the desired output to test on the display
System Check (FAV9800A)While in Service Mode, select System Check on the display
Tub Displacement Sensor Diagnostics1) Enter Service Mode by pressing Help and Back keys for three seconds
Tub Displacement Sensor Diagnostics (FAV6800A)1) Enter Service Mode (Enviro Plus + Spin Only for 3 sec). 2) Press Super Wash key. 3) Press…
Tub Displacement Sensor Diagnostics (FAV9800A)1) Enter Service Mode (Help + Back for 3 sec). 2) Press System Check on display. 3) Push tub to…
User Interface TestEnter Service Mode, then select User Interface and follow the directions on screen.
User Interface Test (FAV9800A)Enter User Interface test from Service Mode and follow the directions on screen.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer, dryer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass