mypros+
Model reference

Modern Maid WCU-516C

Range

5 documents97 error codes25 service modes

Available documentation

Tech Sheet

  • Tech Sheet - do not Discard12 pg
    Covers this model
  • Tech Sheet - W1004649012 pg
    Covers this model
  • Kenmore Whirlpool Range 110 668124P0 110 668124P1 Tech Sheet12 pg
    Covers this model
  • Fiche technique W10667175 RevA8 pg
    Covers this model
  • Fiche technique - Tech Sheet W104416338 pg
    Covers this model
MyPros+ Max

Diagnose your Modern Maid WCU-516C.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (97)

CodeMeaning
F0 E0No failure (default).F0-E0No failure (default).F0E2Over suds condition detectedF0E4High water temperature detected during rinse cycleF0E5Off balance load detected.F1Internal circuit board failure or A/D error (LCC 90/95 display).F1 E0Internal error.F1 E1Internal error.F1 E2Internal error.F1 E3Internal error.F1 E4Internal error.F1 E5Internal error.F1 E6Internal error.F1 E7Internal error.F1 E8Internal error.F1 E9Internal error.F1-E0EEPROM communication error.F1-E1Internal error.F1-E2Internal error.F1-E3Internal error.F1-E4Internal error.F1-E5Sensor out of range.F1-E6Internal error.F1-E7Circuit board thermistor open or short-circuited.F1-E8Internal error.F1-E9Internal error.F1E0Internal circuit board failure (LCC 180/190 display).F1E1Main control fault.F1E2Motor control faultF2Shorted key on touchpad (LCC 90/95 display).
View all 97 error codes
F2 E0Stuck key (shorted key).F2 E1Keypad disconnect or keypad disconnected.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F2E0Shorted key on touchpad (LCC 180/190 display).F2E1Stuck keyF2E3Mismatch of main control and UIF3Oven sensor open circuit (LCC 90/95 display).F3 E0Main oven sensor open (top oven sensor opened).F3 E1Main oven sensor shorted (top oven sensor shorted).F3 E2Meat probe shorted.F3 E4Bottom oven sensor open (bottom/lower oven sensor open).F3 E5Lower/bottom oven sensor shorted.F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Main oven temperature sensor open or short-circuited.F3-E1Main oven sensor short (top oven sensor shorted).F3-E2Oven temperature sensor open or short-circuited (secondary).F3-E4Bottom oven sensor open (bottom oven sensor open).F3-E5Lower sensor short or bottom sensor short (bottom oven sensor shorted).F3-E6Warm drawer sensor open (warming drawer sensor open).F3-E7Warm drawer sensor shorted (warming drawer sensor shorted).F3E0Oven sensor open circuit (LCC 180/190 display).F3E1Pressure sensor faultF3E2Inlet water temperature faultF3E3Oven excessive temperature during clean cycle (LCC 180/190 display).F4 E2Over temperature during cook mode (temperature runaway).F4 E3Over temperature during clean mode (temperature runaway).F4 E7Over temperature cavity 2 (temperature runaway error).F4-E2Over temperature during cook mode.F4-E3Over temperature during clean mode.F4-E7Over temperature cavity 2 (temperature runaway error).F5Door and door position switch mismatch during clean mode (LCC 90/95 display).F5 E0Door latch mismatch (door and latch switches do not agree).F5 E1No operating latch or latch not operating.F5 E2Door switch fault.F5 E4Latch switch fault.F5 E7Unlock door error (cannot unlock door).F5-E0Door and switch mismatch during clean mode.F5-E1Door latch not functional during clean mode.F5-E2Door switch fault.F5-E4Latch switch fault.F5-E7Unlock door errorF5E0Door and door position switch mismatch during clean mode (LCC 180/190 display).F5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF6 E4Lost communication between display board and power board.F6 E5Cancel key error.F6-E1Bake mode excessive temperature (runaway).F6-E2Clean mode excessive temperature (runaway).F6-E3Warming drawer excessive temperature (runaway).F6-E4Lost communication between power board and display board.F6-E5Cancel key error.F7E1Basket speed sensor faultF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8E1Long fillF8E3Overflow conditionF8E5Hot and cold inlet hoses are reversed.F8E6No fillF9Defective house wiring or defective range wiring (LCC 90/95 display).F9E0Defective house wiring or defective range wiring (LCC 180/190 display).F9E1Long drain

Service modes (25)

  • Auto TestFrom Service Mode (TEST ON), press up arrow, '+', or '3' to scroll to AUTO TEST
  • Calibration Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Clean Washer Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until…
  • CONTROL RESETFrom Service Mode, scroll to CONTROL RESET.
  • Diagnostic mode["Press the Cancel key to place the range in an idle state.","Press the Cancel and Start keys in…
  • Diagnostic mode (recall last failure code)["Press the Cancel key to place the range in an idle state.","Press the Cancel and Start keys in…
  • Diagnostic Test Mode (Relay Tests)While in Diagnostic Mode, press the following buttons to test individual relays
  • DISPLAYFrom Service Mode, scroll to DISPLAY.
  • Drain and Spin Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • ENG MODE (Engineering Mode)From Service Mode, scroll to ENG MODE
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • FAULTSFrom Service Mode, scroll to FAULTS.
  • Manual Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until FINAL…
  • MRC Control Module Diagnostic Mode (Service Mode)Press CANCEL > CANCEL > START
  • Quick Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • RELAY USAGEFrom Service Mode, scroll to RELAY USAGE.
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Software Version Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until…
  • Temperature Calibration AdjustmentPress and hold BAKE for 5 seconds
  • TEST MODEFrom Service Mode, scroll to TEST MODE
  • TEST ON (Relay Test Mode)Upon entering service mode (CANCEL>CANCEL>START), TEST ON is displayed
  • UI Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • USAGEFrom Service Mode, scroll to step 1 (USAGE) using up/down arrows.
  • VERSIONFrom Service Mode, scroll to VERSION.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Modern Maid range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass