Model reference

Viking VUD141

Name: Viking VUD141
Brand: Viking

Dishwasher

19 documents10 error codes23 service modes

Available documentation

Service Manual

UNDERCOUNTER DISHWASHER (VUD141) Service Manual22 pg
Covers this model
Viking Range Corporation Undercounter Dishwasher Service Manual22 pg
Covers this model
Viking Range Corporation Undercounter Dishwasher Service Manual20 pg
Covers this model
Dishwasher Service Documentation10 pg
Covers this model
Service Manual Dishwasher Overview47 pg
Covers this model

Wiring Diagram

Wiring Schematics Dishwasher10 pg
Covers this model

Bulletin

New Door Strip1 pg
Covers this model
Unit Stops During Drying Cycle1 pg
Covers this model
New Strainer System1 pg
Covers this model
Ball catch redesign1 pg
Covers this model
New bearing retainer material1 pg
Covers this model
Technical Bulletin - New bearing retainer material1 pg
Covers this model
Technical Bulletin - Redesigned airbreak and locking ring1 pg
Covers this model
Guide pin for door lock stuck or seized1 pg
Covers this model
Guide Pin for Door Lock1 pg
Covers this model
New Lower Rack Dishwasher Wheel1 pg
Covers this model
Dishwasher Rack Repair Kit1 pg
Covers this model
Dishwasher Rack Repair Kit number 027733-0001 pg
Covers this model

Job Aid

Dishwasher Rack Repair Kit Instructions3 pg
Covers this model

MyPros+ Max

Diagnose your Viking VUD141.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Viking Dishwasher

F1 on my Viking VUD141

M+

Temperature stop fault — the

From Service Manual 721261, p.33:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (10)

CodeMeaning

F1Temperature stop fault F2Overfilling F3Thermistor fault F4Water intake fault F5Valve leakage F6Pressure sensor fault F7Pumping out fault F8Blocked filter F9Circulation fault FbSpray arm divider fault

Service modes (23)

DFUD040 Drain Time AdjustmentPress POTS cycle button five times within 15 seconds to enter this mode. Then
DFUD040 Fault Testing (Component Test)Press the RINSE cycle button five times within 15 seconds to enter component test mode. Then
DFUD040 Inlet Time AdjustmentPress CHINA cycle button five times within 15 seconds to enter this mode. Then
DFUD040 Protected StartPress NORMAL cycle button five times within 15 seconds to enter this mode. Then
DFUD042/DFUD142 Service Menu1) Turn off main switch. 2) Wait at least 5 seconds. 3) Keep the Program and Start buttons…
DFUD042/DFUD142 Total Reset1) Turn off main switch
DFUD042/DFUD142 Variant (Variable) SettingsWhen a new control unit is installed, the machine will automatically be in the variant setting menu…
DFUD042/DFUD142 Water Hardness Setting1) Turn off main switch. 2) Wait at least 5 seconds. 3) Keep Start button depressed (S2). 4) Turn…
DFUD140 Drain Time AdjustmentPress QUICK WASH five times, then
DFUD140 Drain Time Adjustment (alternate)Press China (3) five times to enter reprogramming mode. Then
DFUD140 Fault Tracing (alternate button labels)Press TEMP (6) five times, then
DFUD140 Fault Tracing (Component Test)Press TEMPERATURE five times, then
DFUD140 Inlet Time AdjustmentPress ECONOMY five times, then
DFUD140 Protected Start ProgramPress RINSE AND HOLD five times, then
DFUD142 Child Lock Setting1) Turn off main switch. 2) Wait at least 5 seconds. 3) Keep Temperature and Drying selection…
Drain Time Adjustment (DFUD140)Press QUICK WASH five times, then
Drainage Time Program Mode (DFUD140 - J-008 variant)Press 3 five times to enter program mode, then
Extended Fan CoolingPress Pots (1) five times within 15 seconds to enter the changing program. Then
Extra Rinse ProgrammingPress Normal (2) five times within 15 seconds to enter the changing program
Fault Tracing / Component Test Mode (DFUD140)Press TEMPERATURE five times, then press individual cycle buttons to activate components
Inlet Time Adjustment (DFUD140)Press ECONOMY five times, then
Inlet Time Program Mode (DFUD140 - J-008 variant)Press 5 five times to enter program mode, then
Protected Start Program (DFUD140)Press RINSE AND HOLD five times, then

Full entry steps, exit procedures, and test sequences are available in Max.

Related Viking dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass