Model reference

Whirlpool WHIRLPOOLGOLDSXS

Refrigerator

8 documents57 error codes10 service modes

Available documentation

Tech Sheet

Kenmore Whirlpool Dryer 110 C64992300 Tech Sheet 854591012 pg
Covers this model
Kenmore Whirlpool Dryer 110 86742700 Tech Sheet W10143266A12 pg
Covers this model
Whirlpool Refrigerator GI5SVAXVB00 Tech Sheet 128279702 pg
Covers this model

Service Flash

2008 Refrigeration Update1 pg
Covers this model

Other

Whirlpool L5544 pg
Covers this model
Whirlpool Oasis12 pg
Covers this model
whirlpool gold sxs with python dispenser2 pg
Covers this model
Whirlpool Kenmore Front Load Washer Clean Out Procedure2 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WHIRLPOOLGOLDSXS.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Refrigerator

AF on my Whirlpool WHIRLPOOLGOLDSXS

M+

Low inlet air flow detected at install.

From Tech Sheet W10204722, p.14:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (57)

CodeMeaning

AFLow inlet air flow detected at install.F:01Primary control failure.F:02Stuck button or user interface mismatch (appears ONLY in Diagnostic Test Mode).F:20No voltage detected at the heater relay (appears ONLY in Diagnostic Test Mode).F:22Outlet thermistor is open.F:23Outlet thermistor has shorted.F:24Inlet thermistor is open (appears ONLY in Diagnostic Test Mode).F:25Inlet thermistor is shorted (appears ONLY in Diagnostic Test Mode).F:26Motor drive system failure.F:28Moisture sensor strip is open (appears ONLY in Diagnostic Test Mode).F:29Moisture sensor strip has shorted (appears ONLY in Diagnostic Test Mode).F:30Restricted air flow condition exists (appears ONLY in Diagnostic Test Mode).F:31Low voltage condition (less than 30 V) detected (appears ONLY in Diagnostic…F:50No voltage detected at the water valve relay (appears ONLY in Diagnostic Test…F:70No communication between the machine control and the console electronics.F:71No communication between the machine control and the console electronics.F:72Console electronics failure.F:73Console electronics failure.F:74Console electronics failure.F:75Console electronics failure.F:76Console electronics failure.F:77Console electronics failure.F:78Console electronics failure.F0E1Load detected during the washer cleaning cycle.F1E1Central Control Unit (CCU) error F1E2Motor Control Unit (MCU) error F2E2User Interface (UI) software error F2E3Unsupported cycle F3E1Pressure sensor error F3E2Temperature sensor error

View all 57 error codes

F3E4Level or presence sensor error F4E0Heater is not detected F5E1Door switch error F5E2Door lock error F5E3Door unlock error F6E1Communication error between CCU and Motor Control Unit (MCU)F6E2Communication error from UI to CCU F6E3Communication error from CCU to UI F6E5Communication error between CCU and Expansion Board (EB)F7E1Drive motor speed sensing error / washer overload F7E2MCU overheat and/or motor overheat F8E0Steam inlet valve error F8E1No water detected entering washer or pressure sensor trip not detected after 13…F8E2Dispenser system error F8E3Overflow condition F8E4Flow meter fault F9E1Long drain FCE0Communication error, ECM to CCU (model WFL98 only).FCE1Communication error, washer to wireless router (model WFL98 only).FCE2Wireless router cannot communicate with the internet (model WFL98 only).FCE3Antenna A (J2) bad (model WFL98 only).FCE4Antenna B (J11) bad (model WFL98 only).FCE5Current transformer A not functioning (J12) (model WFL98 only).FCE7Provisioning failure L2Low line voltage (less than 30 V) detected at installation.PFPower failure occurred while the dryer was running.SudSuds detected

Service modes (10)

Customer-Focused Drying Mode Adjustment1
diagnostic_test["Begin with a fully assembled dryer connected to a known good power source.","Set Door
Inlet Air Flow Diagnostic1
less_dry_test["Begin with a fully assembled, empty dryer with clean lint screen connected to a known good power…
Line Voltage Diagnostic1
Manual Load Test1. Ensure dryer is in standby mode (plugged in with all indicators off, or with only the Clothes…
Quick Diagnostic Test["Enter Service Diagnostic Mode.","Navigate to Error Diagnostic on the Diagnostics Home…
Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
Service Diagnostic Test Mode1
UI Component Test["Enter Service Diagnostic Mode.","Navigate to Component Activation on the Diagnostics Home…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool refrigerator models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass