mypros+
Model reference

Whirlpool MAT24PR

Washer

1 document24 error codes12 service modes

Available documentation

Service Manual

  • Tech Manual - W11691910 - Rev A48 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool MAT24PR.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (24)

CodeMeaning
F1 E1Indicates a fault has occurred in the main control.F1 E6Control board recognized line voltage below 90 VAC.F2 E1Washer keypad is sensed pressed for continued duration.F3 E2Main control detects an out of range pressure signal.F3 E3Fault is detected when the inlet thermistor is detected to be open or shorted.F5 E1Lid is in locked state, but lid switch is open; the main control cannot detect…F5 E3Lid lock has not moved into locked position or motor cannot be powered; lid is…F5 E4Lid lock has not moved into unlocked position or motor cannot be powered.F6 E1Electrical connection between CCU and UI is damaged; communication failure…F7 E1Main control cannot determine speed of basket, or speed changes too quickly.F7 E2Indicates a fault of the motor control section of the main control.F7 E5Main control cannot determine position of shifter.F8 E1Water level does not change for a period of time or water is present but main…F8 E3Main control senses a water level that exceeds the washer's capacity (overflow…F9 E1Water level does not change after the drain pump is on for 10 minutes (long…FC E1No model/serial number information is saved on the machine's controls.FC E2The model/serial number information saved on the machine's controls is not the…FC E4USB Stick failure (USB full, not detected, or not accessible).FC E5Software uploaded from USB Stick does not match to model number of machine.FC E6Download of machine setup from machine to USB Stick failed (Model Setup Export…FC E7Upload of machine setup from USB Stick to machine failed; machine number from…FP E1Coin 1 circuit error.FP E2Coin 2 circuit error.FP E3Card reader communication failure.

Service modes (12)

  • Help Mode["Enter Service Mode.","Use the NORMAL keypad to advance to program location 2.xx (Special Pricing…
  • P-01 Clear Errors["Enter Service Diagnostic Test Modes.","Display shows 'P-01'.","Press START to clear active error…
  • P-02 Cycle Credit["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-02' is displayed.","Press…
  • P-03 Quick Overview Test["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-03' is displayed.","Press…
  • P-04 Manual Overview Test["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-04' is displayed.","Press…
  • P-05 Calibration Cycle["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-05' is displayed.","Press…
  • P-06 Drain & Spin Cycle["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-06' is displayed.","Press…
  • P-07 UI Diagnostics["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-07' is displayed.","Press…
  • P-09 Tachometer Verification["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-09' is displayed.","Press…
  • P-12 Clean Washer Cycle["Enter Service Diagnostic Test Modes.","Press MIXED to advance until 'P-12' is displayed.","Press…
  • Service Diagnostic Test Modes["For coin (PD) models
  • Set-Up Mode (Programming)["PD Models

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass