mypros+
Error code reference

Amana Washer Error Code od

The door has not been opened after two complete wash cycles

Amana codesAmana washer codes

The door has not been opened after two complete wash cycles. Door switch was not seen open since the last two final spins.

First step from the service manual

If door open sensing, code will be cleared.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for od.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What od means on a Amana washer

The OD error code on an Amana washer indicates that the door has not been opened between wash cycles. Specifically, the control detects this condition when the door switch has not registered an open state following two consecutive complete wash cycles, including their final spins. The washer monitors door switch activity as a way to confirm that laundry is being removed and reloaded between uses. When this normal pattern of use is not detected, the OD code is triggered as an alert.

The door switch is the key component involved in this diagnostic. Each time the door is opened, the switch sends a signal to the control board indicating that the door has transitioned from closed to open. If the control board does not receive this open-door signal after two full cycles have completed, it logs the OD code. This is not necessarily a component failure, but rather a usage pattern flag built into the control logic.

The most straightforward resolution is simply opening the washer door, which clears the code immediately if door open sensing is functioning correctly. If opening the door does not clear the code, the door switch itself may be faulty, with a failed or stuck switch unable to register the open state. Wiring between the door switch and the control board should also be inspected for damage or loose connections if the code persists after the door is opened.

Source: manufacturer service documentation.

Common causes of od

  1. 01

    Door not opened between cycles

    Wiring / connection

    The most likely cause is that the washer completed two full cycles without the door being opened in between. Simply opening the door should clear the code immediately.

  2. 02

    Faulty door switch

    Part replacement

    If the door switch is worn out or stuck in the closed position, it cannot send an open-door signal to the control board even when the door is physically opened. The switch would need to be tested and replaced if found defective.

  3. 03

    Loose or damaged wiring at the door switch

    Wiring / connection

    A loose connector or damaged wire between the door switch and the control board can prevent the open-door signal from reaching the control. Inspect the wiring harness at the switch for corrosion, breaks, or disconnected terminals.

  4. 04

    Control board not reading switch signal

    Part replacement

    In rare cases, the main control board may fail to process the door switch input correctly even when the switch and wiring are functioning. This is typically diagnosed after the switch and wiring have been ruled out.

See the test procedure for each cause

Frequently asked questions about od

What does od mean on a Amana washer?
The OD code on an Amana washer means the door has not been opened after two complete wash cycles. The washer monitors the door switch to confirm the door has been opened between uses, and triggers this code when it does not detect that event. It is primarily a usage alert rather than a component failure. Opening the door is typically all that is needed to clear it.
How do I fix the OD code on my Amana washer?
Start by simply opening the washer door. If door open sensing is working correctly, this action alone will clear the OD code. If the code returns or does not clear after opening the door, inspect the door switch for damage or failure and check the wiring connections between the switch and the control board.
Is the OD error code on an Amana washer a safety issue?
The OD code is not a safety hazard in the traditional sense. It is a control alert designed to flag an unusual usage pattern where the door was not opened between consecutive cycles. The washer may restrict further operation until the condition is addressed, but it does not indicate a dangerous mechanical or electrical failure.
Will resetting my Amana washer clear the OD code?
Opening the washer door is the intended way to clear the OD code, as the control is designed to dismiss it once it detects the door switch opening. A general reset may temporarily clear the display, but if the underlying cause is a faulty door switch or wiring issue, the code is likely to return after the next two completed cycles.
How much does it cost to repair an OD error code on an Amana washer?
If the code clears simply by opening the door, there is no repair cost involved. If the door switch has failed and needs replacement, parts typically range from $15 to $50 depending on the specific switch, with additional labor costs if a technician is hired. Wiring repairs can vary widely based on the extent of the damage.

Related Amana washer codes

All Amana washer codes
View all 33 Amana washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass