mypros+
Model reference

Maytag MAH9700AWW

Washer

27 documents20 error codes14 service modes

Available documentation

Service Manual

  • 27" Front Load Washer Service Manual65 pg
    Covers this model
  • 27" Front Load Washer Service Manual65 pg
    Covers this model
  • Service Manual - 27" Front Load Washer65 pg
    Covers this model
  • Maytag Neptune 27" Front Load Washer L2005-00452 pg
    Covers this model

Service Flash

  • Technical Bulletin - Board Output/Board Input diagnostic test1 pg
    Covers this model
  • Instruction Sheet8 pg
    Covers this model
  • Service Pointer 8178646 Washer Recall2 pg
    Covers this model

Bulletin

  • Technical Bulletin - TDL-0080-S-French Board diagnostic test1 pg
    Covers this model
  • Technical Bulletin - Correct heater installation1 pg
    Covers this model
  • Technical Bulletin - TDL-0082-B-French Restricted Dispenser Hose1 pg
    Covers this model
  • Technical Bulletin - TDL-0082-B Restricted Dispenser Hose1 pg
    Covers this model
  • Technical Bulletin - TDL-0078A-B EC and DC Codes2 pg
    Covers this model
  • Technical Bulletin - TDL-0078A-B EC and DC Codes2 pg
    Covers this model
  • Technical Bulletin - Restricted Dispenser Hose1 pg
    Covers this model
  • Technical Bulletin - TDL-0091-B1 pg
    Covers this model
  • Technical Bulletin - Motion sensor wire harness installation1 pg
    Covers this model
  • Technical Bulletin - TDL-0082-B Restricted Dispenser Hose1 pg
    Covers this model
  • Technical Bulletin TDL-0121-S1 pg
    Covers this model
  • Sourced laundry console removal procedure1 pg
    Covers this model
  • Technical Bulletin - IDL-0003-B-French MAL1800AX Pedestal Installations5 pg
    Covers this model
  • Technical Bulletin - IDL-0003-B MAL1800AX Pedestal Installations5 pg
    Covers this model
  • Technical Bulletin - IDL-0003-B MAL1800AX Pedestal Installations5 pg
    Covers this model
  • Technical Bulletin - Washer Vibration/Walking/Noise on 27" Neptune washers6 pg
    Covers this model
  • Technical Bulletin - Vibration / Walking / Noise Reduction4 pg
    Covers this model

Training

  • Maytag Neptune 27" Front Load Washer52 pg
    Covers this model

Installation Guide

  • Bulletin d'installation - Installations du socle pour la MAL1800AX5 pg
    Covers this model

Other

  • 160272058 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MAH9700AWW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (20)

CodeMeaning
2EVoltage for motor control bus is over or under specified limit (diagnostic…3EMotor failure (Over current)bEMotor tach signal exists without motor running (abnormal condition).dcUnbalance detected during final spin which prevented the spinner from exceeding…dLOpen door lock switch detected with motor running.dSDoor switch is read as open and the door locked switch is read as locked.EDifficulty in reading memory; will not remember machine settings.E2Stuck key detectedE3Motor drive failureFLDoor failed to lock after 3 attempts.HrHeater Relay failureLEWater level sensor faultLODoor failed to unlock after 3 attempts.ndThe water level fails to drop below the Low Water level reset within 15 minutes…nFNo FillodThe door has not been opened after two complete wash cycles; door switch was…OEWater sensor level faultSrSystem Relay failureSUDsWasher is in a suds period; displayed instead of remaining time.tESump thermistor failure

Service modes (14)

  • Board Input TestWhile in Service Mode, press the Spin Only key.
  • Board Output TestWhile in Service Mode, press the Spin Speed key.
  • Board Output Test / System CheckWhile in Service Mode, press the Spin Speed key.
  • Cycle CountWhile in Service Mode, press Chime.
  • Cycle Count DisplayWhile in Service Mode, press Chime key.
  • diagnosticRefer to the Technical Data Sheet shipped with the product for service mode diagnostics entry…
  • Diagnostic Code DisplayWhile in Service Mode, press Rinse&Spin key (displays 'd'), then rotate Cycle Selector knob in…
  • Display Software VersionWhile in Service Mode, press Soil Level key
  • Fast Time Down / Advance to Next StepWhile any test or cycle is running in Service Mode, press the Temperature key to advance program to…
  • Fast Time-Down / Advance to Next StepWhile any test or cycle is running in Service Mode, press the Temperature key to advance the…
  • LED/Switch TestWhile in Service Mode, press the Delay key for 3 seconds, then press individual buttons to test…
  • Quick Service CycleWhile in Service Mode, press Temperature and Soil Level keys simultaneously for 3 seconds.
  • Quick Spin TestWhile in Service Mode, press Delay Start and Rinse&Spin keys simultaneously.
  • Service Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass