Error code reference
Maytag Washer Error Code E
Water sensor level fault
Water sensor level fault – Water level in the machine is believed to be above the overflow level; machine will automatically begin pumping water out until it falls below the overflow level.
First step from the service manual
1
First check to see that water valve is not stuck. If water valve is OK, check water level sensor.
The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.
MyPros+ Max
Get the full diagnostic procedure for E.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·Maytag Washer
E on my Maytag MVW7232HW
M+
Water sensor level fault – Water level in the
From Tech Sheet W12827132, p.24:
1.First check to see that water valve is not stuck. If water valve is OK, check water level sensor.
2.Measure drain pump winding resistance at connector J7 on the main control. Expected: 12 to 16 ohms at room temperature.
3.Back-probe the pump driver output under load. Verify the board switches the pump at 120 VAC during the drain portion of the cycle.
Part W10876537
Drain pump assembly
Related Maytag washer codes
All Maytag washer codes →- ----Inoperative state
- 0No code (no fault present).
- 01Long fill condition
- 1Water drain failure
- 10Unbalance or cabinet hit detected during final spin…
- 11Motor control board not responding or serial communication…
- 12Upper Dryer Thermistor Open Sensed
- 13Upper Dryer Door Circuit Failure
View all 404 Maytag washer codes
- 13ESignal for MAIN PCB is not detected for 10 seconds.
- 15Stuck key
- 16High speed not achieved due to high motor torque
- 17Door actuator switch was not detected open since the final…
- 18Detected lid lock switch open during cycle when not…
- 19Motor Thermal protector opened.
- 1ESump thermistor failure (Optional)
- 2Lower Dryer Thermistor Open Sensed
- 20Filling too quickly during cycle
- 21Losing water during cycle (siphoning)
- 22Door switch detected open during cycle
- 23Door is locked at start of cycle
- 24Motor high RPM detected two times
- 25Motor tachometer signal present without torque command
- 26Rotary Switch 2 left of encoder failed at startup.
- 28Faucet thermistor failure
- 29Sump thermistor failure
- 2EVoltage for motor control bus is over or under specified…
- 3Motor overload
- 30No electrical supply detected at washer or power…
- 31Model ID Unknown, Default model of 31 used.
- 34Welded system relay
- 3EDrive system malfunction
- 4Door lock failure
- 40Load bound up
- 4EWater level sensor fault
- 5Water fill failure
- 50Motor speed/tachometer signal error
- 5ENo Drain
- 6Non Volatile Memory
- 60Heater relay failure or stuck contacts on relay.
- 62Unlock problem
- 6ETemperature control error
- 7Coin input fault
- 70Heater thermistor open or short detected.
- 7ETemperature control error
- 8Water level sensor fault
- 80Door switch/lock system malfunction
- 8EMotor fault
- 90Overflow condition detected
- 9EMalfunction in dryer door circuit.
- b1Blocked coin 1 or coin drop control circuit failure; coin…
- b2Blocked coin 2 or coin drop control circuit failure; coin…
- bEMotor tach signal exists without motor running
- C1Blocked coin 1 or coin drop control circuit failure (coin…
- C2Blocked coin 2 or coin drop control circuit failure (coin…
- CAAverage current limit violation
- CEWater temperature fault
- CIInstantaneous current limit violation
- CLClear to reset cycle counts.
- D-05Coin 1 blocked
- d1Washer door sense error circuit failure on control board…
- d10Door lock sense error or due to power line interference…
- d10/F31Overheating of motor
- d11Motor speed error detected; cycle paused but can be…
- d11/F11Washer MCU error
- d12Motor sense error detected on control board or due to power…
- d12/F25Tachometer error
- d13Blocked coin 2 or coin drop control circuit failure (coin…
- d13 (washer)Washer Coin 2 error
- d14Blocked coin 2 or coin drop control circuit failure (coin…
- d14/F33Pump disconnected
- d15Load inside drum during cleaning washer cycle (Accu Trac…
- d15/F34Load detected in washer during Washer Cleanout Cycle.
- d16Generation 2 debit card reader error
- d16 (washer)Washer Generation 2 debit card reader error
- d17Generation 2 debit card reader error
- d17/F22Door lock error
- d18Dispenser system error (Accu Trac equivalent of F30).
- d19Door unlock error
- d19/F29Door unlock error
- d2Blocked coin 1 or coin drop control circuit failure…
- d2/F22Dryer exhaust thermistor open error
- d20Serial communication error (Accu Trac equivalent of F28).
- d20/F28Communication failure between CCU and MCU.
- d21Overflow condition
- d21/F27Overflow condition
- d22Communication failure from dryer CCU to UIC
- d22 F70Communication failure from CCU to UIC
- d23Communication failure from UIC to dryer CCU
- d23 F71Communication failure from UIC to CCU
- d23/F70Washer communication failure between CCU and UIC.
- d24Temperature sensor error
- d24/F24Temperature sensor error
- d3Water temperature sense error when equipped with…
- d3/F23Dryer exhaust thermistor shorted error
- d3/F73Washer UIC failure
- d3/F74Washer UIC failure
- d36Stuck key error
- d4Dryer motor control circuit error
- d4/F01Dryer motor control circuit error
- d4/F26Door switch error
- d5Coin 1 error
- d5 (washer)Washer Coin 1 error
- d6Blocked coin 1 or coin drop control circuit failure…
- d6/F01Washer CCU error
- d7Slow fill detected; maximum fill time or max continuous…
- d7/F20No water detected entering washer
- d8UIC Microprocessor error (F73) or UIC EEPROM error (F74)
- d8 F73Dryer UIC Microprocessor error
- d8 F74Dryer UIC EEPROM error
- d8/F21Long drain
- d9Voltage detected below 90VAC for 8 seconds (cycle paused…
- d9 (washer)Washer low voltage detection error
- dcDistribute Clothes
- dLDoor lock failure
- doThe washer door must be opened
- doorDoor open error
- dSDoor switch is read as open and the door locked switch is…
- dUDoor Unlock Failure
- E100Communication fault between washer computer and weighing…
- E101Washer weight too low
- E102Washer weight too high
- E103Weight not balanced over 4 load cells (models with weighing…
- E104Weight on individual load cell exceeds maximum (over 1000…
- E105No functional air pressure system
- E11Fill failure
- E12Overfill failure
- E13Heating failure
- E14Heating time failure
- E15Too hot
- E2Stuck key
- E21Overflow failure
- E24Defective level (pressure) sensor detected before start up.
- E25Defective temperature sensor detected during standby mode.
- E26Undefined Mitsubishi frequency inverter error code not…
- E27Communication fault between washer computer and frequency…
- E28THT Time out
- E29OV3/E.OP Time out
- E3Motor drive failure
- E300Specific Mitsubishi inverter alarm (E300-E353 range)…
- E301Mitsubishi inverter overcurrent alarm (OC2).
- E302Mitsubishi inverter overcurrent alarm (OC3).
- E303Mitsubishi inverter overvoltage alarm (OV1).
- E304Mitsubishi inverter overvoltage alarm (OV2).
- E305Mitsubishi inverter overvoltage alarm (OV3).
- E306Mitsubishi inverter overload (THT).
- E307Mitsubishi motor overload (THM).
- E308Inverter cooling fan stopped.
- E309Stall prevention
- E31Initialization fault of the frequency inverter during…
- E310Brake transistor short circuit in brake transistor circuit.
- E311Ground fault
- E313Option fault (OPT)
- E314Corrupt memory
- E315PU leave out
- E316Retry limit reached
- E317CPU fault
- E318CPU Fault 6
- E319CPU Fault 7
- E32Verification fault frequency inverter
- E320Instantaneous power failure between 15 and 100ms.
- E321Under voltage
- E322Output phase failure
- E326PU short circuit on the RS485 communication connector.
- E32724VDC short circuit on the 24VDC power output (PC terminal).
- E335Heatsink overheat
- E341Input phase failure
- E342PTC thermistor operation
- E343Parameter storage error
- E345Inrush overheat
- E35Incorrect software version
- E353Internal circuit error in inverter.
- E36Unbalance detection system activated during the spin…
- E37Drain failure at spray sequence
- E39Soap supplies running out of soap
- E4Safety switch activated during transition from distribution…
- E41Service due warning displayed at the end of a cycle; will…
- E42No network connection during data transfer networking.
- E43Incorrect voltage range selection in the Configuration Menu.
- E44Incorrect machine type selection
- E5Safety switch activated at high revolutions, indicating…
- E500Memory error (E500-E525 range) that can occur at any time.
- E550Internal memory error for traceability data during…
- E551Internal traceability memory is full during traceability…
- E560Error in communication with USB flash disk (E560-E563…
- E561File not found during attempt to read from a USB flash disk.
- E562Export failed
- E563Import failed
- E6Door switch failure detected during wash cycle
- E600Software error
- E7Door lock closing failure
- E8Door lock closing failure at beginning of cycle
- E80Liquid detergent dispensing timeout
- E81No reheat failure (traceability only)
- E82No refill failure (traceability only)
- E83Power interruption
- E85Real time clock has no battery or battery low power…
- E9Door lock opening failure at end of cycle
- E95Watch dog has been activated.
- EdNot receiving communications from installed debit card…
- ErProcessor reset error
- F/02Long drain
- F/05Water temperature sensor (NTC) value is out of range during…
- F/06Drive motor tachometer error
- F/07Motor Control Unit (MCU) error
- F/09Overflow condition
- F/10Motor Control Unit (MCU) heat sink thermal trip
- F/13Dispenser circuit error
- F/14EEPROM error
- F/15Motor Control Unit (MCU) error
- F/dLDoor lock error
- F/dUDoor unlock error
- F/HNo water detected entering machine or pressure switch trip…
- F##System error code (F-type fault).
- F#E#Generic system error code (any F#E# code other than those…
- F01Dryer motor control circuit error
- F03Accelerometer failure
- F03/F04Washer accelerometer failure
- F04Accelerometer failure
- F05 E02Door will not lock
- F08 E01Water supply error
- F09 E01Drain pump system error
- F0E0No fault codes stored in memory.
- F0E1Load detected during Clean Washer cycle; a load was…
- F0E2Over suds condition detected
- F0E3Overload detected; main control detects a load size that…
- F0E4Spin limited by water temperature; water temperature is too…
- F0E5Off balance load condition detected during operation.
- F0E7Control board recognized line voltage below 90 VAC.
- F0E8Water ring fault; too much residual water is detected.
- F0E9Off balance pause
- F1Pressure Signal Out-of-Range
- F11Washer MCU error
- F12Motor sensor circuit failure on control board (machine…
- F1E1ACU error
- F1E2Motor control error
- F2Keypad/User Interface Failure
- F20No water detected entering the washer; the first pressure…
- F21Excessive drain time; the drain operation exceeds eight…
- F22Door lock error; the washer made multiple attempts to lock…
- F23Dryer exhaust thermistor shorted error
- F24Water temperature sensor error
- F25Tachometer error; the MCC cannot correctly detect the motor…
- F26Door switch error
- F27Overflow condition; the overflow switch of the pressure…
- F28Communication failure between CCU and MCU
- F29Not explicitly described in available text (referenced in…
- F2E1Indicates a stuck button (depressed for over 20 seconds) or…
- F2E2User Interface Software Error
- F2E3Mismatch of main control and UI
- F3Water valve thermistor sense failure (too high); washer…
- F30Motor drive error
- F31Overheating of Motor
- F32Long Drain
- F33Pump disconnected; the electrical connection between the…
- F34Load Detected in Washer During Washer Cleanout Cycle
- F35Excessive suds detected during wash cycle and washer could…
- F36Communication Error
- F37Water level out of range low
- F38Water level out of range high
- F3E1Pressure sensor fault; the main control detects an out of…
- F3E2Temperature sensor error
- F3E3Inlet water temperature fault
- F3E4Inlet thermistor is shorted
- F3E5Inlet and exhaust thermistors are open
- F3E6Moisture sensor strip is open
- F3E7Moisture sensor strip has shorted
- F4Board failure in the level circuit; microprocessor board is…
- F40ATC Thermistor Open/Short
- F41Motor RPS Thermistor Open/Short
- F42Heater Thermistor Open/Short
- F43Heater is continuously ON
- F44Heater cannot be turned ON
- F4E0Heater is not detected
- F4E1Wash heater relay error or no feedback signal; ACU cannot…
- F4E2Main heater stuck on; wash heater relay closed.
- F4E3Restricted/low air flow detected that may affect dryer…
- F4E4Low L2 voltage (less than 50V) detected at installation.
- F5Pump driver fails to activate, one of the main relays is…
- F50Motor Stalled
- F51Motor RPS Failure
- F52Motor Stop Failure
- F53Motor control over-temperature
- F54Motor Control Overcurrent
- F5E1Lid switch fault; lid is in locked state but lid switch is…
- F5E2Door lock will not lock or door lock failure; ACU detects…
- F5E3Lid lock has not moved into locked position or motor cannot…
- F5E4Lid not opened between cycles; user presses START after…
- F68Pressure signal out-of-range (saved fault code designation…
- F6E1Communication error; HMI cannot hear ACU, communication…
- F6E2Communication error
- F6E3Communication error ACU to UI
- F7Slow fill detected; fill time greater than 5 minutes…
- F70Communication failure between dryer CCU and UIC
- F71Communication failure from UIC to dryer CCU
- F72Basket Re-engagement Failure
- F73UIC microprocessor error
- F73/F74Washer UIC failure
- F74UI EEPROM not programmed or corrupted
- F77Off balance load detected.
- F7E1Basket speed sensor fault; main control cannot determine…
- F7E2Motor drive circuit over temperature
- F7E3Basket engaged during wash
- F7E4Basket re-engagement failure
- F7E5Shifter fault; main control cannot determine position of…
- F7E6Motor fault
- F7E7Motor unable to reach target RPM
- F7E8Motor over temperature
- F7E9Motor will not turn (locked rotor).
- F7EAMotor control lost phase fault (also displayed as F7E10).
- F7ECMotor control motor overload fault (also displayed as…
- F7EDFault of the motor control section of the main control.
- F8No water detected entering machine or pressure switch trip…
- F80Door Lock Failure
- F81Open/close door lid
- F82Door Lock Failure
- F83Door Unlock Failure
- F84Door Lock Failure
- F85Door Lock Failure
- F8E0Steam inlet valve error (not available on all models)
- F8E1Long fill; water level does not change for a period of time…
- F8E3Overflow condition
- F8E5Hot and cold water supply hoses are reversed.
- F8E6No fill; water level does not change for a period of time…
- F9Low voltage detected; less than 90 volt AC (machine…
- F9E1Drain pump system problem
- FAE1Shipping bolts are still installed.
- FCE0Communication between the Human Machine Interface and Wi-Fi…
- FCE1No model/serial number information is saved on the…
- FCE2Model/serial number information saved on the machine's…
- FCE3Wi-Fi connection fault.
- FCE4USB stick failure (USB full, not detected, or not…
- FCE5Software uploaded from USB stick does not match to model…
- FCE6Download of machine setup from machine to USB stick failed.
- FCE7Upload of machine setup from USB stick to machine failed…
- FCE8Wi-Fi module not responding or not connected.
- FdFactory Default
- FLFlood condition detected
- FPE1Coin 1 circuit error.
- FPE2Coin 2 circuit error.
- FPE3Card reader communication error.
- H-Water temperature control problem.
- h1A temperature increase has not been detected on the lower…
- h11A shaker assembly neutral fault has been detected; shaker…
- HCHot and cold inlet hoses have been installed incorrectly…
- HE1Heater is not heating
- HE2Heater is not heating
- HPThe thermistor reading is out of range and the dryer cycle…
- HrHeater Relay failure
- IEPressure switch error / Water sensor fault
- LWasher is in pause due to the lid being open and unlocked.
- L2Low L2 voltage (less than 50V) detected at installation.
- LdWasher lid sense error on control board or due to power…
- LEWater level sensor fault
- LFWater level detection error on control board or due to…
- lidOpen/Close Door Lid
- LLLarge Load Detected.
- LOLocked; door is locked and failed to unlock
- Lo FLWater supply error
- LrLocked rotor
- LSLid switch error
- LVVoltage detected below 90 VAC for 8 seconds.
- ndNo Drain
- nFNo fill
- nPNo power to motor control or motor not running
- ntInterrupted
- obOut of balance
- odOpen the Door; the door has not been opened since the end…
- OEA fault is detected in the water level sensor
- oLOverloaded
- oPOverflow protection activated
- PWasher is in pause mode due to pressing Pause/Resume pad.
- PAQuick service cycle passed
- PFPower failure
- PoPump Out (lid opened)
- rLLoad inside drum during cleaning washer cycle
- SdSuds lock
- SFProblem with control.
- SrStuck relay
- SuWasher is in suds period
- SudSuds lock
- SUDsExcessive suds detected; washer is in a suds reduction…
- T-01Heating error
- T-02Slow heating
- T-03Over heating condition detected.
- T-04Configuration mismatch between UI and ACU.
- T-05State mismatch between UI and ACU status.
- T-06Load too hot
- T-07No default cycle has been selected.
- T-09Door is open.
- T-10Cycle advance function is disabled.
- T-11Invalid cycle data.
- T-12USB memory stick not detected.
- T-15Tilt switch cycle failure, service required.
- T-17Critical error with multiple sub-error codes indicating…
- T-18Fill dispenser error.
- T-19Water temperature error.
- T-20Water temperature error.
- tEAbnormal high/low temperature or ohm resistance seen from…
- tFWater temperature sense error when equipped with…
- UWasher is in pause due to an unbalance condition.
- UBUnbalance or cabinet hit detected during final spin, which…
- uCContinuous Unbalanced Circuit
- UEUnbalance detected during final spin
- uLUnbalanced Load
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass