Model reference
Maytag MAH8700A
Washer
7 documents19 error codes14 service modes
Available documentation
Tech Sheet
- 27" Front Load Washer⎯Technical Information15 pg
Service Manual
- Maytag Neptune 27" Front Load Washer L2005-00452 pg
Service Flash
- Service Pointer 8178646 Washer Recall2 pg
Bulletin
- Technical Bulletin - Washer Vibration/Walking/Noise on 27" Neptune washers6 pg
- Technical Bulletin - Vibration / Walking / Noise Reduction4 pg
Training
- Maytag Neptune 27" Front Load Washer52 pg
Other
- 160272058 pg
MyPros+ Max
Diagnose your Maytag MAH8700A.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (19)
CodeMeaning
2EVoltage for motor control bus is over or under specified limit.3EOver current is detected; motor won't turn (motor failure).bEMotor tach signal exists without motor running (tach signal exists without…dcUnbalance detected during final spin which prevented the spinner from exceeding…dLOpen door lock switch with motor running (detected door lock switch open during…dSDoor switch is detected open and the door locked switch is read as locked…EDifficulty in reading memory; will not remember machine settings.E2A key is sensed to be pressed more than 30 seconds; the key will be assumed to…E3Machine control is attempting to drive the motor but is not seeing any tach…FLDoor failed to lock after 3 attempts.HrHeater Relay failure; heater relay not sensed.LEA fault is detected in the water level sensor; data (frequency) shows the water…LODoor failed to unlock after 3 attempts.ndThe water level fails to drop below the Low Water level reset within 15 minutes…nFContinuous fill of 12 minutes or total fill of 14 minutes detected (No Fill).odThe door has not been opened after two complete wash cyclesOEWater level in the machine is believed to be above the overflow level (water…SrSystem Relay failure; machine control does not see relay open when it should.tEAbnormal high/low temperature or ohm resistance seen from sump thermistor.Service modes (14)
- Board Input Test["Enter Service Mode.","Press Spin Only key
- Board Output Test["Enter Service Mode.","Press Spin Speed key.","Set Rotary Cycle Selector to desired position and…
- Clear All Diagnostic Codes["Enter Diagnostic Code Display mode.","Press Delay and Chime keys together for 3 seconds while…
- Cycle Count["Enter Service Mode.","Press Soil Level key
- diagnosticRefer to the Technical Data Sheet shipped with the product for service mode diagnostics entry…
- Diagnostic Code Display["Enter Service Mode.","Press Rinse&Spin key
- Display Software Version["Enter Service Mode.","Press Chime key."]
- Fast Time Down / Advance to Next Step["Enter Service Mode.","Press Temperature key to start test.","Press Temperature key during cycle…
- Hold Quick Service Cycle Step["During Quick Service Cycle, press Rinse&Spin and Spin Only keys together."]
- Hold Quick Spin Step["During Quick Spin Test, press the Rotary Selector key."]
- LED/Switch Test["Enter Service Mode.","Press Delay key for 3 seconds.","Then press individual buttons to test LEDs
- Quick Service Cycle["Enter Service Mode.","Press Temperature and Soil Level keys together for 3 seconds."]
- Quick Spin Test["Enter Service Mode.","Press Delay Start and Rinse&Spin keys together."]
- Service Mode["Washer must be powered on.","Press and hold the Chime and Extra Rinse keys for 3 seconds or until…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Maytag washer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass