mypros+
Model reference

Maytag MAH8700AW*

Washer

11 documents19 error codes11 service modes

Available documentation

Service Manual

  • 27" Front Load Washer Service Manual65 pg
    Covers this model
  • Maytag Neptune 27" Front Load Washer L2005-00452 pg
    Covers this model

Service Flash

  • Technical Bulletin TDL-0117-B1 pg
    Covers this model
  • Service Pointer 8178646 Washer Recall2 pg
    Covers this model

Bulletin

  • Technical Bulletin TDL-0118-B1 pg
    Covers this model
  • Technical Bulletin - TDL-0117-B revised rear outer tub and software change1 pg
    Covers this model
  • Bulletin technique - TDL-0117-B-French revised rear outer tub and software change1 pg
    Covers this model
  • Technical Bulletin - Washer Vibration/Walking/Noise on 27" Neptune washers6 pg
    Covers this model
  • Technical Bulletin - Vibration / Walking / Noise Reduction4 pg
    Covers this model

Training

  • Maytag Neptune 27" Front Load Washer52 pg
    Covers this model

Other

  • 160272058 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MAH8700AW*.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (19)

CodeMeaning
2EVoltage for motor control bus is over or under specified limit.3EOver Current is detectedbEMotor tach signal exists without torque command or when not expected (without…dcNever exceeded 400 rpm due to an unbalanced load during final spin.dLOpen door lock switch detected with motor running.dSDoor switch is detected open and the door locked switch is read as locked…EDifficulty in reading memory; will not remember machine settings.E2A key is sensed to be pressed more than 30 seconds; the key is assumed to be…E3Machine control is attempting to drive the motor but is not seeing any tach…FLDoor failed to lock after 3 attempts.HrHeater Relay failureLEWater level sensor faultLODoor failed to unlock after 3 attempts.ndThe water level fails to drop below the Low Water level reset within 15 minutes…nFContinuous fill of 12 minutes or total fill of 14 minutes without reaching…odThe door has not been opened after two complete wash cyclesOEWater level sensor data (frequency) shows the water level is at or above the…SrSystem Relay failuretEAbnormal high/low temperature or ohm resistance seen from sump thermistor.

Service modes (11)

  • Board Input TestWhile in Service Mode, press Spin Only key to begin. Display shows 'in'. Use Rotary Cycle Selector…
  • Board Output TestWhile in Service Mode, press Spin Speed key to begin. Use Rotary Cycle Selector positions and press…
  • Cycle CountWhile in Service Mode, press Chime.
  • diagnosticRefer to the Technical Data Sheet shipped with the product for service mode diagnostics entry…
  • Diagnostic Code DisplayWhile in Service Mode, press Rinse&Spin key
  • Display Software VersionWhile in Service Mode, press Soil Level
  • Fast Time Down / Advance to Next StepWhile any test or cycle is running in Service Mode, press the Temperature key to advance the…
  • LED/Switch TestWhile in Service Mode, press the Delay key for 3 seconds. Then press individual buttons to test per…
  • Quick Service CycleWhile in Service Mode, press Temperature and Soil Level keys for 3 seconds to start. Display shows…
  • Quick Spin TestWhile in Service Mode, press Delay and Rinse&Spin keys to start
  • Service Mode1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass