Model reference

Maytag MAH2400AW

Name: Maytag MAH2400AW
Brand: Maytag

Washer

6 documents28 error codes20 service modes

Available documentation

Service Manual

Compact Washer Base Manual52 pg
Covers this model
Maytag Compact 24" Front Loading Washing Machine Training68 pg
Covers this model
Compact Washer Service Manual52 pg
Covers this model
Neptune Commercial High Efficiency Washer Service Manual124 pg
Covers this model

Tech Sheet

techsheet 16027174f fr14 pg
Covers this model

Bulletin

Technical Bulletin - Washer GFI Circuit Trip Issue1 pg
Covers this model

MyPros+ Max

Diagnose your Maytag MAH2400AW.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Maytag Washer

1E on my Maytag MAH2400AW

M+

Sump thermistor failure (Optional) –

From Tech Sheet W13912035, p.47:

1.Access service mode to confirm the active fault code and read stored error history.

2.Disconnect the sensor and measure resistance. Expected: 10 kΩ to 12 kΩ at 77°F (25°C).

3.Check the sensor harness for opens. A reading outside 5 kΩ to 50 kΩ indicates a failed sensor.

Part WP8577274

Temperature thermistor

Error codes (28)

CodeMeaning

1ESump thermistor failure (Optional)3EDrive system is not working correctly bEMotor tach signal exists without motor running d10Door lock sense error or due to power line interference; spins inhibited until…d11Motor speed error detected; cycle paused but can be restarted.d13Blocked coin 2 or coin drop control circuit failure; coin recognition and price…d16Not receiving communications from installed debit card reader in Generation 2…d17Door was not locked at the beginning of final spin (MAH21 models).d4Washer door sense error on control board or due to power line interference…d5Blocked coin 1 or coin drop control circuit failure; coin recognition and price…d7Slow fill detected during previous cycle; maximum fill time or max continuous…d8Last drain was slow (drain time greater than 2 minutes).d9Low voltage detected; less than 90 volts AC for 8 seconds.dcDistribute Clothes dLLatch Unlocked EWater sensor level fault FLThe washer failed to lock the door.H-Water temperature control problem.LEWater level sensor fault LOThe door will not unlock.LrMotor not running properly.ndNo Drain nFNo Fill odOpen the Door OEWater level sensor error SFProblem with control.tESump thermistor failure.UEUnbalance detected during final spin which prevented the spinner from exceeding…

Service modes (20)

Board Input TestRefer to Technical Sheet or Mini Manual packed behind Toe Panel.
Board Output / System Test["Enter Service Mode.","Press Temperature and Extra Rinse simultaneously to start the Board Output…
Board Output TestRefer to Technical Sheet or Mini Manual packed behind Toe Panel.
Cycle Count DisplayWhile in Service Mode, press Extra Rinse.
Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the slow key (CC will display)."]
Diagnostic Code DisplayWhile in Service Mode, press the Chime key
Diagnostic Mode["Enter the Setup mode (open service door or turn service key).","Press and hold the Delicates &…
Display Software VersionWhile in Service Mode, press Soil Level
Fast Time Down TestWhile any test or cycle is running in Service Mode, press the Spin key.
Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the Woolens keypad to start the field…
Help Mode["Enter Setup mode.","Navigate to Special Pricing Option mode 2.XX.","Press the Permanent Press…
LED/Switch TestWhile in Service Mode, press and hold the Delay Start key.
Operational Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the WHITES keypad to start the…
Quick Service CycleWhile in Service Mode, press the Temperature and Soil Level keys for 3 seconds
Quick Spin Cycle (MAH20 Models)["Enter Diagnostic Mode (entire display flashing).","Press the COLORS keypad to start the quick…
Quick Spin TestWhile in Service Mode, press Delay Start and Temperature keys.
Quick Stop / Advance Step["While in any Service Mode test or cycle, press Spin to initiate Quick Stop."]
Relay Test Mode (MAH20PN)["Enter Diagnostic Mode (entire display flashing).","Press the Permanent Press (lower left) keypad…
Service ModeRefer to Technical Data Sheet located behind Toe Panel for entry procedure.
Setup / Programming Mode["Insert access door key, turn and lift to remove the access door (PD/PS models).","For PN models

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass