mypros+
Model reference

Maytag MAH2440

Washer

2 documents25 error codes20 service modes

Available documentation

Tech Sheet

  • 24" Front Load Washer⎯Technical Information11 pg
    Covers this model

Service Manual

  • Neptune Commercial High Efficiency Washer Service Manual124 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MAH2440.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (25)

CodeMeaning
13ESignal for MAIN PCB is not detected for 10 seconds.3EMotor failure4EWater level sensor fault5ENo Drain8EMotor faultCEWater temperature faultd10Door lock sense error or due to power line interference; spins inhibited until…d11Motor speed error detected; cycle paused but can be restarted.d13Blocked coin 2 or coin drop control circuit failure; coin recognition and price…d16Not receiving communications from installed debit card reader in Generation 2…d17Door was not locked at the beginning of final spin (MAH21 models).d4Washer door sense error on control board or due to power line interference…d5Blocked coin 1 or coin drop control circuit failure; coin recognition and price…d7Slow fill detected during previous cycle; maximum fill time or max continuous…d8Last drain was slow (drain time greater than 2 minutes).d9Low voltage detected; less than 90 volts AC for 8 seconds.doorDoor is openHE1Heater is not heatingHE2Heater is over heatingIEPressure switch error / Water sensor faultLENo FillOEWater sensor level faultPFPower FailuretESump thermistor failureUEUnbalance detected during final spin

Service modes (20)

  • Abbreviated White/Cottons Cycle TestWhile in Service Mode, press the Delay Start button (Four times) followed by the Start/Pause button…
  • Board Output Test (Component Cycle Time Test)While in Service Mode, press the Temperature key (Once) followed by the Start/Pause button
  • Component TestWhile in Service Mode, press the Start/Pause button to cycle through
  • Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the slow key (CC will display)."]
  • Diagnostic Mode["Enter the Setup mode (open service door or turn service key).","Press and hold the Delicates &…
  • EEPROM Test (Board Output Test)Press and hold the Rinse, Prewash and Delay Start buttons, then press the Power On/Off switch
  • Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the Woolens keypad to start the field…
  • Help Mode["Enter Setup mode.","Navigate to Special Pricing Option mode 2.XX.","Press the Permanent Press…
  • LED/Switch TestEnter the Board Output Test, then press the Temperature key (Three times) followed by the…
  • Motor Output TestEnter the Board Output Test, then press the Temperature key (Twice) followed by the Start/Pause…
  • Operational Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the WHITES keypad to start the…
  • Quick Spin Cycle (MAH20 Models)["Enter Diagnostic Mode (entire display flashing).","Press the COLORS keypad to start the quick…
  • Relay Test Mode (MAH20PN)["Enter Diagnostic Mode (entire display flashing).","Press the Permanent Press (lower left) keypad…
  • Rinse And Spin TestWhile in Service Mode, press the Delay Start button (Seven times) followed by the Start/Pause button
  • Service Mode1
  • Setup / Programming Mode["Insert access door key, turn and lift to remove the access door (PD/PS models).","For PN models
  • Spin TestWhile in Service Mode, press the Delay Start button (Six times) followed by the Start/Pause button
  • Thermistor TestWhile in Service Mode, press the Delay Start button (Two times) followed by the Start/Pause button
  • Unbalance TestWhile in Service Mode, press the Delay Start button (Three times) followed by the Start/Pause button
  • White/Cottons Cycle TestWhile in Service Mode, press the Delay Start button (Five times) followed by the Start/Pause button…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass