Model reference
Maytag MAH2400AW*
Washer
5 documents22 error codes17 service modes
Available documentation
Service Manual
- Service Manual - Maytag MAH 2400 Compact Washer52 pg
- Service Manual - Compact Washer52 pg
- Neptune Commercial High Efficiency Washer Service Manual124 pg
Tech Sheet
- techsheet 16027174f fr14 pg
Bulletin
- Technical Bulletin - Unit is counting down to one minute and will not unlock the door1 pg
MyPros+ Max
Diagnose your Maytag MAH2400AW*.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (22)
CodeMeaning
3EDrive system malfunctionbETachometer signal exists without commanded torque when motor is not running…d10Door lock sense error or due to power line interference; spins inhibited until…d11Motor speed error detected; cycle paused but can be restarted.d13Blocked coin 2 or coin drop control circuit failure; coin recognition and price…d16Not receiving communications from installed debit card reader in Generation 2…d17Door was not locked at the beginning of final spin (MAH21 models).d4Washer door sense error on control board or due to power line interference…d5Blocked coin 1 or coin drop control circuit failure; coin recognition and price…d7Slow fill detected during previous cycle; maximum fill time or max continuous…d8Last drain was slow (drain time greater than 2 minutes).d9Low voltage detected; less than 90 volts AC for 8 seconds.dcUnbalanced load prevents high-speed spin; load never exceeds 400 RPM due to…dLLatch unlockedFLDoor did not lock after 3 attempts.LEWater level sensor input signal is out of range; the washer sounds an alarm and…LODoor did not unlock after 3 attempts.ndNo drainnFNo fillodOpen door reminderOEWater level sensor errortECollector thermistor failureService modes (17)
- Board Input TestRefer to Technical Sheet or Mini Manual packed behind Toe Panel for procedure.
- Board Output / System Test["Enter Service Mode.","Press Temperature and Extra Rinse simultaneously to start the Board Output…
- Board Output TestRefer to Technical Sheet or Mini Manual packed behind Toe Panel for procedure.
- Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the slow key (CC will display)."]
- Diagnostic Code Display["Enter Service Mode.","Press Chime to display the first diagnostic code, then rotate the cycle…
- Diagnostic Mode["Enter the Setup mode (open service door or turn service key).","Press and hold the Delicates &…
- Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the Woolens keypad to start the field…
- Help Mode["Enter Setup mode.","Navigate to Special Pricing Option mode 2.XX.","Press the Permanent Press…
- LED/Switch Test["Enter Service Mode.","Press and hold Delay Start to start the LED/Switch test."]
- Operational Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the WHITES keypad to start the…
- Quick Service Cycle["Enter Service Mode.","Press Temperature and Soil Level simultaneously for 3 seconds."]
- Quick Spin Cycle (MAH20 Models)["Enter Diagnostic Mode (entire display flashing).","Press the COLORS keypad to start the quick…
- Quick Spin Test["Enter Service Mode.","Press Delay Start and Temperature simultaneously to start the Quick Spin…
- Quick Stop / Advance Step["While in any Service Mode test or cycle, press Spin to initiate Quick Stop."]
- Relay Test Mode (MAH20PN)["Enter Diagnostic Mode (entire display flashing).","Press the Permanent Press (lower left) keypad…
- Service ModeRefer to Technical Data Sheet located behind Toe Panel for entry procedure.
- Setup / Programming Mode["Insert access door key, turn and lift to remove the access door (PD/PS models).","For PN models
Full entry steps, exit procedures, and test sequences are available in Max.
Related Maytag washer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass