Error code reference

Maytag Washer Error Codes

426 error codes documented with diagnostic procedures.

Have your model number? Get codes specific to your unit.
----Inoperative state-the appliance is inoperative; enter set-up mode to view the diagnostic…0No code (no fault present).01No drain02Door will not unlock after 11 attempts.03No fill04Door will not lock after 11 attempts.05Continuous unbalance circuit during spin only.06Locked rotor07Heater not heating08Water level sensor failure1Water drain failure10Unbalance or cabinet hit detected during final spin prevented the spinner from exceeding…11Upper Dryer Thermistor Short Sensed12Upper Dryer Thermistor Open Sensed13Upper Dryer Door Circuit Failure13ESignal for MAIN PCB is not detected for 10 seconds.15Stuck key16High speed not achieved due to high motor torque17Door actuator switch was not detected open since the final spin18Detected lid lock switch open during cycle when not expected (open lid lock switch with…19Door lock sensor or motor control relay failure1ESump thermistor failure (Optional)-Abnormal high/low temp or ohm resistance seen.2Lower Dryer Thermistor Open Sensed20Filling too quickly during cycle21Sensor switch failure on machine control board22Door switch detected open during cycle23Lid is locked at start of cycle-lid lock is locked and a user tries to start a cycle.24Motor high RPM detected two times-Motor tach signal is seen at maximum speed.25Motor tachometer signal present although the motor is not running26Rotary Switch 2 left of encoder failed at startup.28Faucet thermistor failure29Sump thermistor failure2EVoltage for motor control bus is over specified limit (diagnostic code 91) or under…3Motor overload31Model ID Unknown, Default model of 31 used.34Welded system relay-Change of state of the relay detected.3EDrive system malfunction4Door lock failure40Load bound up-washer not operating due to tumble not functioning; the paddles cannot move.4EWater level sensor fault5Water fill failure5ENo Drain6Non Volatile Memory62Unlock problem6ETemperature control error7Coin input fault7ETemperature control error8Water level sensor fault-input signal from water level sensor is out of range8EMotor fault9EMalfunction in dryer door circuit.b1Blocked coin 1 or coin drop control circuit failure; coin recognition and price display…b2Blocked coin 2 or coin drop control circuit failure; coin recognition and price display…bEMotor tach signal exists without motor running-Tach signal exists without torque…C1Blocked coin 1 or coin drop control circuit failure (coin recognition and price display…C2Blocked coin 2 or coin drop control circuit failure (coin recognition and price display…CAAverage current limit violation-average current draw over 2 seconds exceeded 5.55 amps on…CEWater temperature faultCIInstantaneous current limit violation-an instantaneous spike of 26 amps on the motor…CLClear to reset cycle counts.CLOSE DOOR PRESS STARTA wash cycle was selected and Start was pressed while the door is still open, or a…D-05Coin 1 blockedd1Washer door sense error circuit failure on control board (machine non-functional on…d10Door lock sense error or due to power line interference; spins inhibited until corrected…d10/F31Overheating of motor-heat sink exceeds 212°F (100°C); CCU resets MCU and waits for motor…d11Motor speed error detected; cycle paused but can be re-started (machine functional).d11/F11Washer MCU error-Motor Control Unit has a failure, possibly a repeating under or…d12Door switch errord12/F25Tachometer error-MCU is unable to properly detect motor speed; washer shuts down.d13Blocked coin 2 or coin drop control circuit failure (coin recognition and price display…d13 (washer)Washer Coin 2 error-the Coin 2 sensor is detected as blocked for 8 seconds.d14Blocked coin 2 or coin drop control circuit failure (coin recognition and price display…d14/F33Pump disconnected-electrical connection between the pump and the CCU is lost.d15Load inside drum during cleaning washer cycle (Accu Trac equivalent of F34).d15/F34Load detected in washer during Washer Cleanout Cycle.d16Generation 2 debit card reader errord16 (washer)Washer Generation 2 debit card reader error-no communication from installed debit card…d17Generation 2 debit card reader errord17/F22Door lock error-washer unable to lock the door after multiple attempts.d18Dispenser system error-dispenser unable to reach desired position.d19Door unlock errord19/F29Door unlock error-door is unable to unlock after 6 tries.d2Blocked coin 1 or coin drop control circuit failure (machine non-functional on original…d2/F22Dryer exhaust thermistor open error-temperature drops below 18°F (>50 kΩ) for 1 minute in…d20Serial communication error (Accu Trac equivalent of F28).d20/F28Communication failure between CCU and MCU.d21Overflow conditiond21/F27Overflow condition-overflow contact on pressure switch is closed for more than 60 seconds.d22Communication failure from dryer CCU to UICd22 F70Communication failure from CCU to UIC-UIC is not receiving communications from CCU…d23Communication failure from UIC to dryer CCUd23 F71Communication failure from UIC to CCU-CCU is not receiving communications from UIC…d23/F70Washer communication failure between CCU and UIC.d24Temperature sensor errord24/F24Temperature sensor error-water temperature sensor value is out of range (23°F to 217°F /…d3Water temperature sense error when equipped with temperature sensing water valve (cycles…d3/F23Dryer exhaust thermistor shorted error-temperature above 250°F (<500Ω) for 1 minute in…d3/F73Washer UIC failure-communication error within the User Interface Control, possibly caused…d3/F74Washer UIC failure-communication error within the User Interface Control, possibly caused…d36Stuck key errord4Dryer motor control circuit errord4/F01Dryer motor control circuit error-control cannot determine if motor relay is bad (stuck…d4/F26Door switch error-door switch circuit is open for 5 seconds while door is locked.d5Coin 1 errord5 (washer)Washer Coin 1 error-the Coin 1 sensor is detected as blocked for 8 seconds.d6Blocked coin 1 or coin drop control circuit failure (machine non-functional on original…d6/F01Washer CCU error-communication error within the Central Control Unit; pump drive in CCU…d7Slow fill detected; maximum fill time or max continuous fill time reached, cycle paused…d7/F20No water detected entering washer-first level of pressure switch is not tripped after 6…d8UIC Microprocessor error (F73) or UIC EEPROM error (F74)d8 F73Dryer UIC Microprocessor error-UIC Microprocessor is not able to read or verify EEPROM…d8 F74Dryer UIC EEPROM error-UIC EEPROM memory is a CRC failure (cycles and price display…d8/F21Long drain-drain time exceeds 8 minutes without reaching reset level in pressure switch.d9Voltage detected below 90VAC for 8 seconds (cycle paused but can be restarted on original…d9 (washer)Washer low voltage detection error-incoming voltage detected below 90 VAC for 8 seconds.dcImbalance detected or cabinet bumping during final spin, preventing spinner from…dLDoor lock failuredoThe washer door must be openeddoorDoor open errorDOOR FAILThe door safety system has failed during the wash cycle; all other machine functions are…DRAIN FAILUREWater was not drained from the machine within the set time; drain valve stays open and…dSDoor switch is read as open and the door locked switch is read as locked (door/lid switch…dUDoor Unlock FailureEWater sensor level fault-Water level in the machine is believed to be above the overflow…E100Communication fault between washer computer and weighing system signal conditioner…E101Washer weight too lowE102Washer weight too highE103Weight not balanced over 4 load cells (models with weighing system only), prevents start.E104Weight on individual load cell exceeds maximum (over 1000 kg) during wash cycle (weighing…E105No functional air pressure systemE11Fill failureE12Overfill failureE13Heating failureE14Heating time failureE15Too hotE2Stuck keyE21Overflow failureE24Defective level (pressure) sensor detected before start up.E25Defective temperature sensor detected during standby mode.E26Undefined Mitsubishi frequency inverter error code not recognized by washer computer.E27Communication fault between washer computer and frequency inverterE28THT Time outE29OV3/E.OP Time outE3Motor drive failureE300Specific Mitsubishi inverter alarm (E300-E353 range) occurring during the whole cycle.E301Mitsubishi inverter overcurrent alarm (OC2).E302Mitsubishi inverter overcurrent alarm (OC3).E303Mitsubishi inverter overvoltage alarm (OV1).E304Mitsubishi inverter overvoltage alarm (OV2).E305Mitsubishi inverter overvoltage alarm (OV3).E306Mitsubishi inverter overload (THT).E307Mitsubishi motor overload (THM).E308Inverter cooling fan stopped.E309Stall preventionE31Initialization fault of the frequency inverter during parameter set-up; inverter not…E310Brake transistor short circuit in brake transistor circuit.E311Ground faultE313Option fault (OPT)E314Corrupt memoryE315PU leave outE316Retry limit reachedE317CPU faultE318CPU Fault 6E319CPU Fault 7E32Verification fault frequency inverterE320Instantaneous power failure between 15 and 100ms.E321Under voltageE322Output phase failureE326PU short circuit on the RS485 communication connector.E32724VDC short circuit on the 24VDC power output (PC terminal).E335Heatsink overheatE341Input phase failureE342PTC thermistor operationE343Parameter storage errorE345Inrush overheatE35Incorrect software versionE353Internal circuit error in inverter.E36Unbalance detection system activated during the spin sequence; spinning revolutions are…E37Drain failure at spray sequenceE39Soap supplies running out of soapE4Safety switch activated during transition from distribution into spin sequence…E41Service due warning displayed at the end of a cycle; will keep occurring until the cycle…E42No network connection during data transfer networking.E43Incorrect voltage range selection in the Configuration Menu.E44Incorrect machine type selectionE5Safety switch activated at high revolutions, indicating probable mechanical defect.E500Memory error (E500-E525 range) that can occur at any time.E550Internal memory error for traceability data during traceability function.E551Internal traceability memory is full during traceability function.E560Error in communication with USB flash disk (E560-E563 range), occurs only in advanced…E561File not found during attempt to read from a USB flash disk.E562Export failedE563Import failedE6Door switch failure detected during wash cycleE600Software errorE7Door lock closing failureE8Door lock closing failure at beginning of cycleE80Liquid detergent dispensing timeoutE81No reheat failure (traceability only)E82No refill failure (traceability only)E83Power interruptionE85Real time clock has no battery or battery low power, detected at end of cycle.E9Door lock opening failure at end of cycleE95Watch dog has been activated.EdNot receiving communications from installed debit card reader in Enhanced (Generation 2)…EEPROM FAILA storage location in the EEPROM memory does not function properly.ErProcessor reset error-the control failed to save cycle information during a power failure…F/02Long drainF/05Water temperature sensor (NTC) value is out of range during the water heating step in the…F/06Drive motor tachometer errorF/07Motor Control Unit (MCU) errorF/09Overflow conditionF/10Motor Control Unit (MCU) heat sink thermal tripF/13Dispenser circuit errorF/14EEPROM errorF/15Motor Control Unit (MCU) errorF/dLDoor lock errorF/dUDoor unlock errorF/HNo water detected entering machine or pressure switch trip not detected after water…F##System error code (F-type fault).F#E#Generic system error code (any F#E# code other than those specifically listed).F01Dryer motor control circuit errorF03Accelerometer failureF03/F04Washer accelerometer failure-the X, Y, and Z limits are outside of the normal range.F04Accelerometer failure-the accelerometer component failed; X, Y, and Z limits are outside…F05 E02Door will not lock-washer door is not locking properly.F08 E01Water supply error-water is not being supplied properly to the washer.F09 E01Drain pump system error-washer is unable to drain properly.F0E0No fault codes stored in memory.F0E1Load detected inside the drum during the Clean Washer cycle.F0E2Over suds condition detectedF0E3Overload detected; main control detects a load size that exceeds the washer's capacity or…F0E4Spin limited by water temperature; water temperature is too high to spin at final speed…F0E5Off balance load condition detected during operation.F0E7Control board recognized line voltage below 90 VAC.F0E8Water ring fault; too much residual water is detected.F0E9Off balance pauseF1Pressure Signal Out-of-Range-the control detects an out-of-range pressure signal.F11Washer MCU errorF12Motor sensor circuit failure on control board (machine functional).F12E0Communication between the Human Machine Interface and Wi-Fi Module has not been detected…F1E1ACU errorF1E2Motor control errorF2Keypad/User Interface FailureF20No water detected entering the washer; the first pressure switch threshold is not…F21Excessive drain time; the drain operation exceeds eight minutes without reaching the…F22Door lock error; the washer made multiple attempts to lock the door and failedF23Dryer exhaust thermistor shorted error-temperature above 120°C (250°F) (<500 Ω) for 1…F24Water temperature sensor errorF25Tachometer error; the MCC cannot correctly detect the motor speed, causing the washer to…F26Door switch errorF27Overflow condition; the overflow switch of the pressure switch is closed for more than 60…F28Communication failure between CCU and MCUF29Door unlock failure-referenced in communication/motor overheating troubleshooting context.F2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatchF2E2User Interface Software ErrorF2E3Mismatch of main control and UIF3Water valve thermistor sense failure (too high); washer remains operative.F30Motor drive errorF31Overheating of MotorF32Long DrainF33Pump disconnected; the electrical connection between the pump and the MCC is lost…F34Load Detected in Washer During Washer Cleanout CycleF35Excessive suds detected during wash cycle and washer could not resolve conditionF36Communication ErrorF37Water level out of range lowF38Water level out of range highF3E1Pressure sensor fault; the main control detects an out of range pressure signal.F3E2Temperature system errorF3E3Inlet water temperature faultF3E4Inlet thermistor is shortedF3E5Inlet and exhaust thermistors are openF3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4Board failure in the level circuit; microprocessor board is inoperable.F40ATC Thermistor Open/Short-the ATC (Automatic Temperature Control) thermistor is detected…F41Motor RPS Thermistor Open/Short-the motor rotor position sensor (RPS) thermistor is…F42Heater Thermistor Open/ShortF43Heater is continuously ON-the heater is ON when it should be OFF.F44Heater cannot be turned ONF4E0Heater is not detectedF4E1Wash heater relay error or no feedback signal; ACU cannot detect temperature rise of the…F4E2Main wash heater is stuck on (heater relay closed).F4E3Restricted/low air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at installation.F5Pump driver fails to activate, one of the main relays is not working properly, or a…F50Motor Stalled-the motor rotor position sensor (RPS) senses no rotation.F51Motor RPS FailureF52Motor Stop Failure-the motor rotor position sensor (RPS) senses rotation after a Stop…F53Motor control over-temperatureF54Motor Control Overcurrent-the machine/motor control detects high current for the motor…F5E1Lid switch fault; lid is in locked state but lid switch is open, or main control cannot…F5E2Door lock will not lock or door lock failure; ACU detects open door switch when…F5E3Lid lock has not moved into locked position or motor cannot be powered; possible lock…F5E4Lid not opened between cycles; user presses START after consecutive cycles without…F68Pressure signal out-of-range (saved fault code designation for F then 1 display).F6E1Communication error; HMI cannot hear ACU, communication between HMI and ACU has not been…F6E2Communication error ACU to UIF6E3Communication error UI to ACUF6E5Communication error between ACU and Expansion Board (EB)F7Slow fill detected; fill time greater than 5 minutes (machine functional).F70Communication failure between dryer CCU and UICF71Communication failure from UIC to dryer CCUF72Basket Re-engagement Failure-the basket check routine fails to determine if the basket is…F73UIC microprocessor errorF73/F74Washer UIC failure-communication error within the User Interface Control, possibly due to…F74UI EEPROM not programmed or corruptedF77Off balance load detected.F7E1Basket speed sensor fault; main control cannot determine speed of basket or speed changes…F7E10Motor disconnected error.F7E12MC/MCU overload.F7E2Motor drive circuit over temperatureF7E3Basket engaged during washF7E4Basket re-engagement failureF7E5Shifter fault; main control cannot determine position of shifterF7E6Motor fault-indicates an open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPMF7E8Motor over temperatureF7E9Motor lock rotorF7EAMotor disconnected error (alternate display for F7E10).F7ECMC/MCU overload (alternate display for F7E12).F7EDFault of the motor control section of the main control.F8No water detected entering machine or pressure switch trip not detected; pressure switch…F80Door Lock FailureF81Open/close door lidF82Door Lock FailureF83Door Unlock FailureF84Door Lock FailureF85Door Lock FailureF8E0Steam inlet valve error (not available on all models)F8E1No fill / long fill-water level does not change for a period of time or water is present…F8E2Dispenser system errorF8E3Overflow conditionF8E5Hot and cold water supply hoses are reversed.F8E6No fill; water level does not change for a period of time or water present but main…F9Low voltage detected; less than 90 volt AC (machine functional).F9E1Long drainFAE1Shipping bolts are still installed.FCE0Communication between the Human Machine Interface and Wi-Fi Module has not been detected…FCE1No model/serial number information is saved on the machine's controls.FCE2Model/serial number information saved on the machine's controls is not the same between…FCE3Wi-Fi connection fault.FCE4USB stick failure (USB full, not detected, or not accessible).FCE5Software uploaded from USB stick does not match to model number of machine.FCE6Download of machine setup from machine to USB stick failed.FCE7Upload of machine setup from USB stick to machine failed; machine number from downloaded…FCE8Wi-Fi module not responding or not connected.FdFactory DefaultFILL FAILWater level did not reach the programmed level within the microprocessor pre-set time…FLNo lockFPE1Coin 1 circuit error.FPE2Coin 2 circuit error.FPE3Card reader communication error.H-Water temperature control problem.h1A temperature increase has not been detected on the lower dryer and the dryer advances to…h11A shaker assembly neutral fault has been detected; shaker relay is de-energized and cycle…HCHot and cold inlet hoses have been installed incorrectly (reversed).HE1Heater is not heatingHE2Heater is not heatingHEAT FAILRegistered temperature did not reach the programmed target temperature within the…HPThe thermistor reading is out of range and the dryer cycle is interrupted.HrHeater Relay failureIEPressure switch error / Water sensor faultLWasher is in pause due to the lid being open and unlocked.L2Low L2 voltage (less than 50V) detected at installation.LdWasher lid sense error on control board or due to power line interference (cycles and…LEWater level sensor faultLFWater level detection error on control board or due to power line interference (cycles…lidOpen/Close Door LidLLLarge Load Detected.LOLocked; door is locked and failed to unlockLoFLNo water detected entering washer or water level sensor trip not detected (saved as…LrLocked rotorLSLid switch error-control cannot correctly detect lid switch open/close, or discrepancy…LVVoltage detected below 90 VAC for 8 seconds.ndNo DrainnFNo fillNO PROCESSA non-programmed wash cycle was selected and the Start keypad was pressed.ntInterruptedobOut of balance-the motor controller detected an unrecoverable out-of-balance condition.odOpen the Door; the door has not been opened since the end of the last cycleOEA fault is detected in the water level sensoroLOverloaded-the machine/motor control detects a load size that exceeds the washer's…OPLid is openOUT OF BALANCEThe out-of-balance safety switch has tripped approximately eight times in a row during…OVERLOAD FAULTMotor has become thermally overloaded or motor contactor is overloaded; all other machine…PWasher is in pause mode due to pressing Pause/Resume pad.PAQuick service cycle passedPAUSEThe SIGNAL function has been programmed in a particular step requiring operator action…PFPower failurePoPump Out (lid opened)PROCESS COMPLETE PLEASE WAITThe wash cycle has completed and the machine is finishing final operations.PROCESS MEMORY EXCEEDMemory capacity has been exceeded during programming of a wash cycle when inserting a…rLLoad inside drum during cleaning washer cycleSdSuds lockSERVICE DUEThe number of completed wash cycles has reached the target figure pre-set in the…SFProblem with control.SrStuck relay-relay failure in the closed position; power to the motor controller cannot be…SuWasher is in suds periodSudSuds lock condition detectedSUDsExcessive suds detected; washer is in a suds reduction period instead of displaying…T-01Heating errorT-02Slow heatingT-03Over heating condition detected.T-04Configuration mismatch between UI and ACU.T-05State mismatch between UI and ACU status.T-06Load too hotT-07No default cycle has been selected.T-09Door is open.T-10Cycle advance function is disabled.T-11Invalid cycle data.T-12USB memory stick not detected.T-15Tilt switch cycle failure, service required.T-17Critical error with multiple sub-error codes indicating micro faults, software flow…T-18Fill dispenser error.T-19Water temperature error.T-20Water temperature error.tECollector thermistor failuretFWater temperature sense error when equipped with temperature sensing water valve (cycles…TOO HOTTemperature probe records temperature above 50°C (122°F) when the door may normally be…TOO HOT CHECK HEATINGThe heating sensor recorded a temperature that is 2.5°C (25°F) higher than programmed.UWasher is in pause due to an unbalance condition.UBUnbalance or cabinet hit detected during final spin, which prevented the spinner from…uCContinuous Unbalanced CircuitUEUnbalance detected during final spin-spinner never exceeded 400 rpm due to an unbalanced…uLUnbalanced LoadWATER IN CAGEWater is still in the cage at the moment when the door may normally be opened; door lock…

Get the full diagnostic procedure for any code

Step-by-step tests, expected values, wiring diagram references, and verified part numbers.

Get Started $9.95 3-day pass

$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.