Skip to main content
Error code reference
Maytag Range Error Codes
107 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
1c1cShorted key detected in membrane switch; disables audible feedback for affected key and…1c2cKeyboard tail disconnected1c31Cancel key circuit problem; A/D reading out of range, disables audible for affected key…1c32Cancel key circuit problem (H1 models)1c4cMicro communication failure-serial communications checksum invalid between…1c5cVcc or ground failure-Vcc/ground at testpoint out of specification during cook active…1c6cEEPROM error1c7cControl not calibrated; calibration value out of range1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error1d11Runaway temperature (650°F) with door unlocked1d12Runaway temperature (650°F) detected with door unlocked in lower oven; door unlock sensor…1d21Runaway temperature (950°F) with door locked-sensor resistance greater than 2787 ohms…1d22Runaway oven temperature (950°F) with door locked3d11Temperature sensor open3d12Lower oven meat probe sensor resistance is infinite (open circuit)3d21Temperature sensor shorted3d22Lower oven meat probe sensor resistance > 0 ohms (shorted)3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch position failure4d12Door switch is not closed when door is locked4d21No reverse airflow fan rotation (no/low RPM)4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse airflow fan state (on when should be off)4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch is neither open nor closed (indeterminate state)4d52Lower oven door switch circuit failure; switch not reading open or closed during convect…5a6Sabbath Mode active status indicator (not a fault code)5AbSabbath Mode is active (status indicator, not a fault code).9d11Latch will not lock9d12Lock switch not closed (lock position not detected)9d21Latch will not unlock9d22Unlock switch not closed (unlock position not detected)9d31Latch state unknown-both locked and unlocked switches closed simultaneously; disables…9d32Door latch state unknown9d41Unlock state unknown9d42Latch state unknown9d51Lock switch not locked or unlockedBAKEBAKE flashing rapidly in the display indicates an error or problem with the oven control…DOORLock status is not sensed within 20 seconds of energizing door lock relay.EEControl cannot read EEPROM; unit will shut down.FFault code displayed as 'F' plus a number, indicating an oven control or component fault…F-0Surface elementF-5Surface elementF0-0No fault present (default from factory).F0:0No fault detected.F1Error in control circuitry; monitors relay outputs or heating function when in…F1-1Runaway cook condition in upper ovenF1-2Runaway cook condition in lower ovenF1-3Runaway clean condition in upper ovenF1-4Runaway clean condition in lower ovenF1-5Upper hardware failure within control.F1-6Lower hardware failure within control.F1-7Membrane switch is not responding.F1-8Shorted key (pad) in membrane switch.F1-9Internal communication errors within control.F1-AUpper oven latch switch failureF1-BLower oven latch switch failureF1-CUpper oven door open fault (door position switch not closed).F1-DLower oven door open fault (door position switch not closed).F1-EEEPROM failure on control board.F1-FJumper not removed from printed circuit board (PCB).F1-HEEPROM read error on control board.F1-LSensor wire fault-open sensor wire detected when an oven is active.F1-NInternal voltage for slave micro incorrect.F1:1Oven temperature exceeds 650°F (runaway condition in bake mode).F1:2Oven temperature exceeds 950°F (runaway condition in clean mode).F1:3Shorted key in membrane switch.F1:4Membrane switch disconnected.F1:5Cancel key not responding.F1:7Slave microprocessor not functioning.F1:8EEPROM error.F1:9Control not calibrated.F1:ALatch switch failure.F1:CDoor switch failure.F1:EControl not calibrated.F1:FJumper wire disconnected.F1:HEEPROM read failure in control.F1:NVCC failure in control.F2Bake/Broil/Clean temperature runaway alarm; sounds alarm and resets control to non-cook…F2:1Door state input circuitry failure.F3Open wire lead in sensor harness, bad harness/sensor connection, or sensor resistance too…F3-1Upper oven sensor is shorted (below 100 ohms) or open (above 5K ohms).F3-2Lower oven sensor is shorted (below 100 ohms) or open (above 5K ohms).F3:1Oven sensor is shorted or open.F4Sensor resistance too low (below 500 ohms)F6Missing AC Line Cycle Detector; resets control to non-cook mode if AC line cycles are…F7Missing AC line cycle detector; displays code (no audible) and resets control to non-cook…F8Function key shorted; sounds alarm and resets control to non-cook mode if a function key…F9Door Latch Supervisory (Door Latched)F9-1Latch switch fault, upper oven-detected when latch is locked.F9-2Unlock switch fault, upper oven-detected when latch is locked.F9-3Upper oven lock and unlock switch both in error.F9-4Lock switch fault, lower oven-detected when latch is locked.F9-5Unlock switch fault, lower oven-detected when latch is locked.F9-6Lower oven lock and unlock switch both in error.F9:1Door lock will not lock.FCCommunication error between boards (power relay board side).FFOven temperature is above 585°F and door circuitry has a problem after 16 seconds.FODoor latch supervisory (door latched); sounds alarm and resets control to non-cook mode…FRSecond oven error sensed (double oven only).LOCKLOCK flashing rapidly in the display indicates an error or problem with the oven door…SAbOven is operating in Sabbath Mode (continuous operation up to 72 hours with all…
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Maytag error codes
Common questions
How do I find the error code on my Maytag Range?
Most Maytag ranges show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Maytag ranges. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.