mypros+
Error code reference

Maytag Range Error Code F1

Error in control circuitry; monitors relay outputs or heating function when in time-of-day mode, shuts system down to safe condition; also monitors…

Maytag codesMaytag range codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F1 error code actually means

The F1 error code means your Maytag range has detected a problem with its internal control system, either because the oven got too hot or because the board that runs the oven is not working correctly. This can happen during normal cooking if the oven temperature climbs beyond safe limits, around 550 degrees Fahrenheit, or if the control board itself develops a fault. Until this is resolved, the oven may not operate safely or reliably.

Diagnostic procedure

The full F1 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check oven sensor for correct ohm value or for charred connector; if sensor is OK, replace the control.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F1 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F1

Ranked by how often they cause this code
  1. 1Failed or out-of-range oven temperature sensor
  2. 2Charred or damaged sensor connector
  3. 3Actual over-temperature condition in the oven cavity
  4. 4Faulty electronic control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F1

What does F1 mean on a Maytag range?
F1 on a Maytag range signals a fault in the control board's circuitry, specifically in how it monitors relay output or heating function during operation. It also triggers when the oven detects an over-temperature condition, such as the bake mode exceeding approximately 550°F. The two most common sources are a failed oven temperature sensor and a faulty control board.
Is it safe to use my Maytag range while the F1 code is showing?
No, you should not continue using the oven while F1 is active. This code can indicate that the oven temperature exceeded 550°F, which is a potential fire and food safety hazard. It can also indicate a stuck relay that keeps a heating element energized when it should be off. Disconnect power to the range and do not operate the oven until the fault is diagnosed and repaired.
Will clearing the F1 code on my Maytag range fix the problem?
Clearing the code by cutting power to the range will stop the display and may allow temporary use, but it does not fix the underlying fault. If the oven sensor is failing or the control board has an internal fault, F1 will return during the next cooking cycle. Use the power reset only to confirm whether the code is persistent, then proceed with sensor testing before ordering parts.
How do I fix the F1 error code on my Maytag range?
Start by testing the oven temperature sensor with a multimeter. At room temperature, the sensor should read around 1,080 to 1,100 ohms. Also inspect the sensor's wiring connector inside the oven for any charring or melting. If the sensor and connector are both in good condition, the electronic control board has failed and needs to be replaced. Both repairs are within reach for a confident DIYer comfortable with appliance disassembly.
How much does it cost to repair an F1 error on a Maytag range?
An oven temperature sensor typically costs between $20 and $60 for the part and is one of the easier range repairs to perform yourself. If the control board is the cause, the board itself generally runs between $150 and $350 depending on the model, and professional installation adds another $100 to $200 in labor. Diagnosing the sensor first is worthwhile since it is the cheaper and more common failure.

Related Maytag range error codes

All Maytag range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass