mypros+
Error code reference

Maytag Range Error Code F1-B

Lower oven latch switch failure

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F1-B error code actually means

Your Maytag range is displaying F1-B because the oven's control board is not receiving a proper signal from the door locking mechanism during a self-clean cycle. Basically, the oven cannot confirm whether the door is locked or unlocked, so it stops the self-clean process as a safety measure. This is typically caused by a wiring connection issue or a faulty door latch assembly.

Diagnostic procedure

The full F1-B procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check that lower latch switch is closed.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F1-B procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F1-B

Ranked by how often they cause this code
  1. 1Damaged or disconnected latch wire harness
  2. 2Failed lower latch switch
  3. 3Faulty door latch assembly
  4. 4Failed oven control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F1-B

What does the F1-B error code mean on a Maytag range?
F1-B means the control board has detected a failure in the lower latch switches, which are part of the oven door latch assembly. These switches tell the board whether the oven door is locked or unlocked. The code typically appears when attempting or running a self-clean cycle, because the board cannot confirm a valid locked door signal from those switches.
Can I still use my Maytag range with an F1-B error code?
Standard baking and cooking functions are generally still usable when F1-B is active, since this code is tied to the latch switch circuit used for self-clean operations. However, the self-clean cycle will not operate safely or at all with this fault present. Continued use for everyday cooking is typically safe, but the underlying latch switch issue should be resolved before attempting another self-clean cycle.
Will clearing the F1-B code fix the problem on a Maytag range?
Clearing the code by unplugging the range or using the control panel will remove the displayed error temporarily, but the code will return as soon as the self-clean cycle is initiated again if the underlying latch switch or wiring issue has not been repaired. Clearing the code is useful for resetting the board after you have made a repair, but it is not a fix on its own.
How do I fix the F1-B error on my Maytag range?
Start by inspecting the latch wire harness for any loose connectors, pinched wires, or corrosion at the terminals. Unplug the range, locate the harness running from the lower latch switch assembly to the control board, and reseat all connectors. If the harness is intact, use a multimeter to test the lower latch switches for continuity in both the locked and unlocked positions. A switch that shows no continuity change needs to be replaced along with the latch assembly.
How much does it cost to fix a Maytag range F1-B error?
If the fix is simply reseating a loose harness connector, there is no parts cost and only your time. A replacement door latch assembly for a Maytag range typically runs between $40 and $90 for the part. If a professional technician is needed, expect a service call fee plus one to two hours of labor, bringing the total repair to roughly $150 to $250 depending on your area and the specific model.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass