Surface element: any relay drive opens during cook mode; display will indicate F-1 after power is removed and reapplied.
MyPros+ Max
Get the full diagnostic procedure for F-5.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·Maytag Range
F-5 on my Maytag Range
M+
Surface element: any relay drive opens during
From Tech Sheet W17465560, p.12:
1.Access service mode to confirm the active fault code and read stored error history.
2.Measure line voltage at the power cord terminal block. Expected: 120 VAC (L1 to neutral) or 208 to 240 VAC between L1 and L2 under load.
3.Inspect the cord strain relief and terminal block screws for signs of arcing or heat discoloration. Loose connections here mimic an intermittent power failure to the control board.
Part W10911048
Power cord assembly
Related Maytag range codes
All Maytag range codes →- 1c1cShorted key detected in membrane switch; disables audible…
- 1c2cKeyboard tail disconnected
- 1c31Cancel key circuit problem; A/D reading out of range…
- 1c32Cancel key circuit problem (H1 models)
- 1c4cMicro communication failure
- 1c5cVcc or ground failure
- 1c6cEEPROM error
- 1c7cControl not calibrated; calibration value out of range
View all 106 Maytag range codes
- 1c81Cook profile corrupted in EEPROM for upper/single oven…
- 1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC…
- 1c8cCooking program error
- 1d11Runaway temperature (650°F) with door unlocked
- 1d12Runaway temperature (650°F) detected with door unlocked in…
- 1d21Runaway temperature (950°F) with door locked
- 1d22Runaway oven temperature (950°F) with door locked
- 3d11Temperature sensor open
- 3d12Lower oven meat probe sensor resistance is infinite (open…
- 3d21Temperature sensor shorted
- 3d22Lower oven meat probe sensor resistance > 0 ohms (shorted)
- 3d41Meat probe shorted
- 3d51Meat probe not calibrated
- 4d11Door switch position failure
- 4d12Door switch is not closed when door is locked
- 4d21No reverse airflow fan rotation (no/low RPM)
- 4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven…
- 4d31Reverse airflow fan state (on when should be off)
- 4d32Reverse Airflow Fan state error
- 4d41High Reverse Airflow Fan rotation (high RPM) on…
- 4d42High Reverse Airflow Fan rotation (high RPM) on lower oven…
- 4d51Door switch is neither open nor closed (indeterminate state)
- 4d52Lower oven door switch circuit failure; switch not reading…
- 5a6Sabbath Mode active status indicator (not a fault code)
- 5AbSabbath Mode is active (status indicator, not a fault code).
- 9d11Latch will not lock
- 9d12Lock switch not closed (lock position not detected)
- 9d21Latch will not unlock
- 9d22Unlock switch not closed (unlock position not detected)
- 9d31Latch state unknown
- 9d32Door latch state unknown
- 9d41Unlock state unknown
- 9d42Latch state unknown
- 9d51Lock switch not locked or unlocked
- BAKEBAKE flashing rapidly in the display indicates an error or…
- DOORLock status is not sensed within 20 seconds of energizing…
- EEControl cannot read E-PROM; unit will shut down.
- FFault code displayed as 'F' plus a number, indicating an…
- F-0Surface element
- F0-0No fault present (default from factory).
- F0:0No fault detected.
- F1Error in control circuitry; monitors relay outputs or…
- F1-1Runaway cook condition in upper oven
- F1-2Runaway cook condition in lower oven
- F1-3Runaway clean condition in upper oven
- F1-4Runaway clean condition in lower oven
- F1-5Upper hardware failure within control.
- F1-6Lower hardware failure within control.
- F1-7Membrane switch is not responding.
- F1-8Shorted key (pad) in membrane switch.
- F1-9Internal communication errors within control.
- F1-AUpper oven latch switch failure
- F1-BLower oven latch switch failure
- F1-CUpper oven door open fault (door position switch not…
- F1-DLower oven door open fault (door position switch not…
- F1-EEEPROM failure on control board.
- F1-FJumper not removed from printed circuit board (PCB).
- F1-HEEPROM read error on control board.
- F1-LSensor wire fault
- F1-NInternal voltage for slave micro incorrect.
- F1:1Oven temperature exceeds 650°F (runaway condition in bake…
- F1:2Oven temperature exceeds 950°F (runaway condition in clean…
- F1:3Shorted key in membrane switch.
- F1:4Membrane switch disconnected.
- F1:5Cancel key not responding.
- F1:7Slave microprocessor not functioning.
- F1:8EEPROM error.
- F1:9Control not calibrated.
- F1:ALatch switch failure.
- F1:CDoor switch failure.
- F1:EControl not calibrated.
- F1:FJumper wire disconnected.
- F1:HEEPROM read failure in control.
- F1:NVCC failure in control.
- F2Bake/Broil/Clean temperature runaway alarm; sounds alarm…
- F2:1Door state input circuitry failure.
- F3Open wire lead in sensor harness, bad harness/sensor…
- F3-1Upper oven sensor is shorted (below 100 ohms) or open…
- F3-2Lower oven sensor is shorted (below 100 ohms) or open…
- F3:1Oven sensor is shorted or open.
- F4Sensor resistance too low (below 500 ohms)
- F6Missing AC Line Cycle Detector; resets control to non-cook…
- F7Missing AC line cycle detector; displays code (no audible)…
- F8Function key shorted; sounds alarm and resets control to…
- F9Door Latch Supervisory (Door Latched)
- F9-1Latch switch fault, upper oven
- F9-2Unlock switch fault, upper oven
- F9-3Upper oven lock and unlock switch both in error.
- F9-4Lock switch fault, lower oven
- F9-5Unlock switch fault, lower oven
- F9-6Lower oven lock and unlock switch both in error.
- F9:1Door lock will not lock.
- FCCommunication error between boards (power relay board side).
- FFOven temperature is above 585°F and door circuitry has a…
- FODoor latch supervisory (door latched); sounds alarm and…
- FRSecond oven error sensed (double oven only).
- LOCKLOCK flashing rapidly in the display indicates an error or…
- SAbOven is operating in Sabbath Mode (continuous operation up…
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass