Skip to main content
Error code reference
Maytag Oven Error Codes
120 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
1c1cKey stuck/shorted1c2cKeyboard tail disconnected; keyboard loop returning improper value.1c31Cancel key circuit problem (upper oven / single cavity)-cancel key improper value.1c32Cancel key circuit problem (lower oven); cancel key returning improper value.1c4cMicro-communication failure1c5cVcc or ground fault1c6cEEPROM error1c7cControl not calibrated; calibration value out of range1c81Cook profile corrupted in EEPROM (upper oven / single cavity)-CRC invalid.1c82Cook profile corrupted in EEPROM (lower oven)-UH1/2 control only.1c8cCooking program error1d11Aberrant temperature with door unlocked1d12Runaway temperature (650°F) detected with door unlocked (lower oven); sensor resistance >…1d21Aberrant temperature with door locked1d22Runaway temperature (950°F) detected with door locked (lower oven); sensor resistance >…3d11Runaway temperature with door unlocked3d12Temperature sensor failure (open) in lower oven; sensor resistance greater than infinite…3d21Runaway temperature with door locked3d22Temperature sensor failure (short) in lower oven; sensor resistance less than 0 ohms.3d31Meat probe open (single cavity or upper oven).3d41Meat probe shorted (probe resistance <0 Ω), upper oven (UH1/2 control only).3d42Meat probe shorted in lower cavity, probe resistance less than 0 ohms.3d51Meat probe not calibrated4d11Door switch position failure-door switch not closed when door is locked (upper oven or…4d12Door switch position failure, door switch not closed when door is locked (lower cavity).4d21No reverse airflow fan rotation (no/low RPM) during cook or clean (upper oven or single…4d22No Reverse Airflow Fan rotation (no/low RPM) during cook or clean (lower oven, UH control…4d31Fan state error4d32Reverse airflow fan state error4d41High reverse airflow fan rotation (high RPM) during cook or clean (upper oven)-UH1/2 only.4d42High reverse airflow fan rotation (high RPM) during cook or clean (lower oven)-UH1/2 only.4d51Door switch circuit failure-door switch not open or closed (upper oven or single cavity).4d52Door switch circuit failure (lower oven); door switch not reading open or closed.9d11Door lock mechanism does not function9d12Motorized door latch will not lock, lock switch not closed (lower cavity).9d21Door unlock mechanism does not function9d22Motorized door latch will not unlock, unlock switch not closed (lower cavity).9d31Latch state unknown-both locked and unlocked switches indicate closed simultaneously…9d32Latch both locked and unlocked simultaneously in lower cavity; lock and unlock switches…9d41Latch neither locked nor unlocked in upper cavity; neither lock nor unlock switches…9d42Latch neither locked nor unlocked in lower cavity; neither lock nor unlock switches…9d51Lock and unlock state unknown9d61Door position switch open circuit during cleaningA0Main board failure.A2Display board failure.B0Touch panel failure.B1Touch panel failure.C-0Temp Sensor (RTD) open circuit.C-1Temp Sensor (RTD) shorted.C-2Temp Sensor (RTD) out of range.C-81Over temperature on induction cooktop (Type 2 failure)-not enough ventilation.C-82Over temperature on induction cooktop (Type 2 failure)-not enough ventilation.C-83Induction cooktop temperature sensor stuck (Type 2 failure).D-0Thermocouple (RTD) open circuit.D-1Thermocouple (RTD) shorted.D-2Thermocouple (RTD) out of range.doorLock status is not sensed within 90 seconds of energizing door lock relay; door flashes…FFault code indicated by F followed by a number appearing in the display, indicating a…F-0Suspect the electronic control.F-12Induction cooktop coil under current (Type 1 failure, affects only one burner).F-2The electronic control has received an indication from the oven sensor that the oven has…F-21Induction cooktop supply power frequency error (Type 2 failure, affects all burners on…F-25Stuck fan on Induction Power System (IPS)-right or left side fan depending on which side…F-36Induction cooktop temperature sensor is not working (Type 1 failure).F-37Induction cooktop temperature sensor is not working (Type 1 failure).F-4Suspect a shorted oven sensor or oven sensor wiringF-40Induction Power System (IPS) failure (Type 1 or Type 2).F-42Induction cooktop power supply issue (Type 2 failure).F-43Induction cooktop under voltage (Type 2 failure).F-47Power supply from Induction Power Control (IPC) to User Interface is missing, or WIDE…F-56Wrong or invalid configuration (Type 3 failure-disables entire cooktop).F-58Wrong or invalid configuration (Type 2 failure).F-6Suspect the electronic control.F-60User Interface does not work (Type 3 failure-disables entire cooktop).F0E0No error(s) foundF1Internal circuit board failure or A/D error(s) (F1E0, F1E1, F1E2 on LCC 180/190 displays).F13WIDE (Appliance Manager-UI) communication error.F1E0EEPROM Communication Error-the main control is locked up due to an unexpected…F1E1Internal errorF1E2Lower RTD Uncalibrated-the main control is locked up due to the lower A/D not being…F1E5Sensor Usage Out of Range-the main control is locked up due to an internal issue with a…F1E7PCB Thermistor Open or Shorted-the main control is locked up due to an onboard…F1E9WIDE Queue Full-the main control is locked up due to the data bus being full.F2E0Keypad Disconnected-the main control no longer sees the keypad.F2E1Stuck Keypad-the main control has detected a keypad has been pressed for an extended…F2E2Cancel or Off Key Error/Warming Zone Off Keypad Error-the Cancel/Off or Warming Zone Off…F3Oven sensor opened, oven sensor shorted, BAKE/BROIL range over temperature, or CLEAN…F3E0Main Sensor Open or Shorted (Upper)-the main control has detected an upper cavity…F3E1Main Sensor Open or Shorted (Lower)-the main control has detected a lower cavity…F3E2Warming drawer sensor shorted (oven not equipped with this feature; indicates wrong user…F3E3Self-clean-excessive temperature.F5Door and door position switch mismatch during clean mode (F5E0/F5E2 on LCC 180/190…F5E0Door and Latch Switches Do Not Agree-the main control detects the door is locked when it…F5E1Latch Not Operating-the door latch will neither lock nor unlock; latch motor runs 3…F5E2Door and switches do not agree (Clean mode).F6E0Lost WIDE Communication-communication was lost between the main control and a cooktop…F6E1Over Temp Cook-the control detects an oven temperature >601°F (316°C) when not in a…F6E2Over Temp Clean-the control detects an oven temperature >900°F (482°C) when in a…F6E3Mini oven/warm drawer over temperature (not for built-in ovens).F6E4User interface / appliance manager mismatch.F6E5Cavity size is incorrect.F7Function key shortedF8Display board memory communication error.F8E0Low fan speed underspeedF8E1Low fan speed overspeedF8E2High fan speed underspeedF8E3High fan speed overspeedF9Failure of door lock switch or door jamb switch circuitry (door locked condition).F9E0Miswired-the product is miswired.FFFailure of door lock switch sensing with door unlocked (ERC4800/ERC5800).FRSecond oven error sensed.G-0Oven exceeded maximum temperature.G-2Magnetron TCO tripped or cooling motor failure.H-0Signal missingH-1Main board set point incorrect.H-2Main board failure.H-3Main board failure.M-0Current sense low amps on both magnetrons.M-1Magnetron 1 low amps.M-2Magnetron 2 low amps.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.