mypros+
Error code reference

Maytag Oven Error Code 9d42

Latch neither locked nor unlocked in lower cavity; neither lock nor unlock switches closed.

Maytag codesMaytag oven codes

Latch neither locked nor unlocked in lower cavity; neither lock nor unlock switches closed.

MyPros+ Max

Get the full diagnostic procedure for 9d42.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 9d42 means on a Maytag oven

Error code 9d42 on a Maytag oven indicates that the door latch mechanism in the lower cavity is in an indeterminate state. Specifically, neither the lock switch nor the unlock switch is registering a closed circuit. During normal operation, the latch assembly should fully complete travel to one of two defined positions: fully locked or fully unlocked. Each position is confirmed by a corresponding switch closure that signals the control board the latch has reached its endpoint. When neither switch closes, the control board cannot confirm the latch position and triggers this fault.

The latch assembly in the lower cavity is a motorized mechanism used primarily during self-clean cycles to secure the oven door. It includes a latch motor, a latch bar or arm, and two position-sensing switches (lock and unlock). If the latch motor stalls mid-travel, if the mechanical components are obstructed or worn, or if either switch has failed open, the control board will see no confirmation of position and generate the 9d42 code. Wiring harness issues between the switches and the control board can produce identical symptoms.

Diagnosing this fault requires inspecting the latch assembly for physical obstructions or binding, testing the latch motor for correct operation, and checking continuity on both the lock and unlock switches individually. Wiring connections at the latch assembly connector and at the control board should also be inspected for corrosion, loose pins, or damage. If the motor runs but the latch does not complete travel, the mechanical linkage or latch bar may be the source of the problem.

Source: manufacturer service documentation.

Common causes of 9d42

  1. 01

    Failed or stalled latch motor

    Part replacement

    The latch motor may have burned out or stalled mid-travel, preventing the latch from reaching either the locked or unlocked position. Check if the motor runs when activated and inspect it for signs of overheating or mechanical binding.

  2. 02

    Defective latch position switch

    Part replacement

    Either the lock switch or the unlock switch (or both) may have failed open, meaning they no longer close the circuit even when the latch reaches the correct position. Test each switch for continuity at its activated position to confirm.

  3. 03

    Mechanical obstruction or worn latch linkage

    Wiring / connection

    Debris, grease buildup, or worn mechanical components in the latch assembly can prevent the latch bar from completing its full range of travel. Inspect the latch mechanism for anything blocking movement and check for worn or broken linkage parts.

  4. 04

    Wiring harness fault

    Wiring / connection

    A broken wire, corroded connector, or loose pin in the wiring between the latch switches and the control board can prevent switch signals from reaching the board. Inspect the harness and connectors at both ends for damage or poor contact.

  5. 05

    Faulty control board

    Part replacement

    If the latch motor, switches, and wiring all test correctly, the control board itself may not be reading the switch inputs properly. This is the least common cause and should be considered only after all other components have been ruled out.

See the test procedure for each cause

Frequently asked questions about 9d42

What does 9d42 mean on a Maytag oven?
Error code 9d42 means the door latch in the lower oven cavity is not completing its travel to either the locked or unlocked position. The control board monitors two position switches on the latch assembly, and neither is reporting a closed circuit. This typically points to a problem with the latch motor, the position switches, the mechanical latch linkage, or the wiring connecting these components to the control board.
Can I reset the 9d42 code on my Maytag oven to clear it?
Resetting the oven by cutting power at the breaker or unplugging it may temporarily clear the code, but it is unlikely to resolve the underlying problem. If the latch motor, switches, or wiring have a physical fault, the code will return as soon as the control board attempts to verify latch position again. A reset is worth trying as a first step, but a proper diagnosis of the latch system is needed for a lasting fix.
Is it safe to use my Maytag oven when the 9d42 code is showing?
You should avoid running the self-clean cycle while this code is active, since the oven cannot confirm that the door is securely locked before reaching self-clean temperatures. Basic baking or broiling may still function depending on how the oven responds to the fault, but it is best to address the latch issue before relying on the oven for normal use. Consult a qualified technician if you are unsure whether the oven is safe to operate.
How much does it cost to fix a 9d42 error on a Maytag oven?
Repair costs depend on which component has failed. A replacement latch motor or switch assembly typically runs anywhere from $40 to $120 for parts alone, while a control board can range from $150 to $350 or more. Adding professional labor costs, total repair bills commonly fall between $100 and $500 depending on the fault and your location. Getting a diagnosis first helps avoid replacing parts unnecessarily.
How do I fix the 9d42 error code on my Maytag oven?
Start by cutting power to the oven for a few minutes and restoring it to see if the code clears. If it returns, inspect the lower oven door latch area for any visible obstructions or debris that could be blocking latch movement. From there, the latch motor, the lock and unlock position switches, and the wiring harness all need to be tested for proper operation and continuity. If you are not comfortable working with electrical components inside an oven, a professional appliance technician should perform the diagnosis and repair.

Related Maytag oven codes

All Maytag oven codes
View all 103 Maytag oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass