mypros+
Error code reference

Maytag Oven Error Code 1c7c

Control not calibrated; calibration value out of range

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 1c7c error code actually means

Your oven's control board has detected a problem with its internal temperature calibration settings. These settings tell the oven how to heat accurately, and they appear to be corrupted or missing. Until this is resolved, the oven may display 'CAL' on the clock display or shut down completely to prevent unsafe operation.

Diagnostic procedure

The full 1c7c procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Recalibrate or replace control; control disables lights and timers.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 1c7c procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 1c7c

Ranked by how often they cause this code
  1. 1Corrupted calibration data in the control board
  2. 2Failed or defective control board
  3. 3Power surge or brownout event
  4. 4Improper manual calibration adjustment

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 1c7c

What does error code 1C7C mean on a Maytag oven?
Error code 1C7C means the control board has detected a calibration value that is outside its acceptable range. The board either displays 'CAL' in the time digits or disables all oven outputs as a safety response. The calibration data is stored inside the control board, so the fix targets that component directly rather than sensors or heating elements.
Can I still use my Maytag oven when error code 1C7C is active?
In most cases, no. When 1C7C is active, the control board either shows 'CAL' in the time display or disables all outputs entirely, meaning the oven will not heat or respond to controls. Even if limited function appears available, operating the oven with an uncalibrated control board means temperature accuracy cannot be trusted, which creates both cooking and safety concerns. Resolve the fault before using the oven.
Will resetting my Maytag oven clear the 1C7C error code?
A power reset may clear 1C7C temporarily if the calibration data was corrupted by a one-time power event. Disconnect the oven from power for at least 5 minutes, then restore power and check if the code returns. If 1C7C comes back after the reset, the control board's stored calibration value is either permanently corrupted or the board itself has failed, and replacement is required.
How do I fix error code 1C7C on a Maytag oven?
The primary fix for 1C7C is replacing the control board. Before ordering a part, try a hard reset by disconnecting power to the oven for 5 minutes. If the code returns after restoring power, the calibration data is not recoverable through a reset and the control board needs to be replaced. Match the replacement board to your exact model number, as calibration parameters vary by model.
How much does it cost to fix a Maytag oven with error code 1C7C?
A replacement Maytag oven control board typically costs between $150 and $350 depending on the model. If you hire a technician, expect an additional $100 to $200 in labor, bringing the total repair to roughly $250 to $550. Replacing a control board is a manageable DIY task for someone comfortable working with appliance electronics. The board connects via wiring harness plugs, and the work does not require special tools beyond basic hand tools and precautions for working with capacitors.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass